Votos - 0, Puntuación media: 0
(
)
)
|
Otros manuales para este modelo:
Resumen del manual
If you use excessive force, you may damage the connector. 6. Slide the new hard drive into the bay and into the connector until it is fully seated. 7. Replace the two hard drive screws. Back to Contents Page Back to Contents Page Hinge Cover Dell Precision™ M65 Mobile Workstation Service Manual 1. Follow the procedures in Before You Begin. 2. Turn the computer top-side up, and then open the display all the way (180 degrees) so that it rests on your work surface. 3. Insert a scribe in the indent to carefully pry up the hinge cover on the right side. 4. Ease the hinge cover up, moving from right to left, and remove it. To replace the hinge cover, insert the left edge of the cover into the hinge cover slot, and press from left to right until the cover snaps into place. Back to Contents Page CAUTION: Before you begin any of the procedures in this section, follow the safety instructions in the Product Information Guide. NOTICE: To avoid electrostatic discharge, ground yourself by using a wrist grounding strap or by periodically touching an unpainted metal surface (such as a connector on the back of the computer). NOTICE: The hinge cover is fragile and can be damaged if extreme force is used. Be careful when removing the hinge cover. NOTICE: To avoid damaging the hinge cover, do not lift the cover on both sides simultaneously. 1 hinge cover 2 indent Back to Contents Page Keyboard Dell Precision™ M65 Mobile Workstation Service Manual 1. Follow the procedures in Before You Begin. 2. Remove the hinge cover (see Hinge Cover). 3. Remove the three screws at the top of the keyboard. 4. Rotate the keyboard forward and lay it on the palm rest to allow access to the keyboard connector on the system board. 5. Pull up on the pull-tab to disconnect the keyboard cable connector from the keyboard connector on the system board. 6. To replace the keyboard, connect the keyboard cable connector to the keyboard connector on the system board. 7. Place the tabs along the front edge of the keyboard into the palm rest and lay the keyboard down on the palm rest. 8. Replace the three screws at the top of the keyboard. 9. Replace the hinge cover. Back to Contents Page CAUTION: Before working inside your Dell™ computer, follow the safety instructions in your Product Information Guide. CAUTION: To prevent static damage to components inside your computer, discharge static electricity from your body before you touch any of your computer's electronic components. You can do so by touching an unpainted metal surface. NOTICE: The keycaps on the keyboard are fragile, easily dislodged, and time-consuming to replace. Be careful when removing and handling the keyboard. 1 keyboard 2 keyboard screws 3 keyboard cable connector 4 keyboard connector NOTICE: To avoid scratching the palm rest when replacing the keyboard, hook the tabs along the front edge of the keyboard into the palm rest, and then secure the keyboard in place. Back to Contents Page Memory Dell Precision™ M65 Mobile Workstation Service Manual The computer has two memory slots, DIMM A and DIMM B. DIMM A is located on top of the computer under the keyboard, and DIMM B is located on the bottom of the computer under the memory module cover. DIMM A holds the basic memory module as configured from the factory. If you did not order additional memory, DIMM B is empty. Generally, if you add memory, you use DIMM B. If you are upgrading memory, you may need to install memory in DIMM A and DIMM B, depending on the extent of the upgrade. To install a memory module in DIMM A: 1. Follow the procedures in Before You Begin. 2. Remove the hinge cover (see Hinge Cover). 3. Remove the keyboard (see Keyboard). 4. Ground yourself by touching one of the metal connectors on the back of the computer. 5. If you are replacing a memory module, remove the existing module: a. Use your fingertips to carefully spread apart the securing clips on each end of the memory module connector until the module pops up. b. Remove the module from the connector. 6. Ground yourself and install the new memory module: a. Align the notch in the module edge connector with the tab in the connector slot. b. Slide the module firmly into the slot at a 45-degree angle, and rotate the module down until it clicks into place. If you do not feel the click, remove the module and reinstall it. CAUTION: Before you begin any of the procedures in this section, follow the safety instructions in the Product Information Guide. NOTICE: If your computer has only one memory module, install the memory module in the connector labeled "DIMMA." NOTICE: If you remove your original memory modules from the computer during a memory upgrade, keep them separate from any new modules that you may have, even if you purchased the new modules from Dell. If possible, do not pair an original memory module with a new memory module. Otherwise, your computer may not function at optimal performance. NOTE: Memory modules purchased from Dell are covered under your computer warranty...