Votos - 0, Puntuación media: 0
(
)
)
|
Otros manuales para este modelo:
Resumen del manual
2. Replace the M2.5 x 8-mm screw to secure the optical drive to the system board. 3. Replace the bottom of the base assembly (see Replacing the E5400 Bottom of the Base Assembly or Replacing the E5500 Bottom of the Base Assembly). 4. Follow the procedures in After Working on Your Computer. Back to Contents Page CAUTION: Before you begin any of the procedures in this section, follow the safety instructions that shipped with your computer. For additional safety best practices information, see the Regulatory Compliance Homepage on at: 1 optical drive 2 M2.5 x 8-mm screw CAUTION: Before you begin any of the procedures in this section, follow the safety instructions that shipped with your computer. For additional safety best practices information, see the Regulatory Compliance Homepage on at: NOTE: This procedure assumes that you have completed the removal procedure first. Back to Contents Page Palm Rest Dell™ Latitude™ E5400 and E5500 Service Manual Removing the E5400 Palm Rest Replacing the E5400 Palm Rest Removing the E5500 Palm Rest Replacing the E5500 Palm Rest Removing the E5400 Palm Rest 1. Follow the instructions in Before Working on Your Computer. 2. Remove the bottom of the base assembly (see Removing the E5400 Bottom of the Base Assembly). 3. Remove the hard drive (see Removing the Hard Drive). 4. Remove the WLAN card (see Removing a WLAN Card). 5. Remove the hinge cover (see Removing the Hinge Cover). 6. Remove the keyboard (see Removing the Keyboard). 7. Remove the display assembly (see Removing the E5400 Display Assembly). 8. Remove the optical drive (see Removing the Optical Drive). 9. Remove the 13 M2.5 x 8-mm screws from the bottom of the computer. 10. Remove the four M2.5 x 5-mm screws on the top of the computer securing the metal plate. 11. Remove the three M2 x 3-mm screws that secure the top of the computer near the display. CAUTION: Before you begin the following procedure, follow the safety instructions that shipped with your computer. For additional safety best practices information, see the Regulatory Compliance Homepage on at: 1 M2.5 x 8-mm screws (13) NOTE: The screw locations may vary slightly on your computer. 12. Be sure that all screws securing the palm rest are removed. 13. Gently pry the palm rest from the bottom of the computer. 14. Before separating the palm rest assembly from the bottom of the computer, carefully remove the speaker and touchpad wires from the system board. 15. Remove the palm rest assembly from the computer. Replacing the E5400 Palm Rest 1. Carefully reconnect the speaker and touchpad cables to the system board 2. Align the palm rest with the computer base and gently snap it into place. 3. Replace the 13 M2.5 x 8-mm screws to the bottom of the palm rest 4. Replace the three M2 x 3-mm screws at the top of the palm rest near the display. 5. Replace the four M2.5 x 5-mm screws on the top of the computer securing the metal plate. 6. Replace the optical drive (Replacing the Optical Drive). 7. Replace the display assembly (see Replacing the E5400 Display Assembly). 8. Replace the keyboard (see Replacing the Keyboard). 9. Replace the hinge cover (see Replacing the Hinge Cover). 10. Replace the processor heat sink (see Replacing the Processor Heat Sink). 11. Replace the fan (see Replacing the Fan). 12. Replace the WLAN card (see Replacing a WLAN Card). 1 palm rest 2 dashboard LED board connector 3 M2.5 x 5-mm screws (4) 4 M2 x 3-mm screws (3) 5 computer base 6 touch pad connector 7 speaker connector NOTICE: Do not use force to separate the palm rest from the computer. If you encounter resistance, gently flex or apply pressure to the palm rest, or move along the edge, working away from the area of resistance, until the palm rest is free. CAUTION: Before you begin the following procedure, follow the safety instructions that shipped with your computer. For additional safety best practices information, see the Regulatory Compliance Homepage on at: NOTICE: Ensure that the touch pad cable and the speaker cable are properly routed before snapping the palm rest into place. NOTE: This procedure assumes that you have completed the removal procedure first. 13. Replace the hard drive (see Replacing the Hard Drive). 14. Replace the bottom of the base assembly (see Replacing the E5400 Bottom of the Base Assembly). 15. Follow the procedures in After Working on Your Computer. Removing the E5500 Palm Rest 1. Follow the instructions in Before Working on Your Computer. 2. Remove the bottom of the base assembly (see Removing the E5400 Bottom of the Base Assembly). 3. Remove the hard drive (see Removing the Hard Drive). 4. Remove the WLAN card (see Removing a WLAN Card). 5. Remove the hinge cover (see Removing the Hinge Cover). 6. Remove the keyboard (see Removing the Keyboard). 7. Remove the dis...