Votos - 0, Puntuación media: 0
(
)
)
|
Otros manuales para este modelo:
Resumen del manual
1. Align the pin-1 corner of the microprocessor module with the pin-1 corner of the ZIF socket, and insert the microprocessor module. When the microprocessor module is correctly seated, all four corners are aligned at the same height. If one or more corners of the module are higher than the others, the module is not seated correctly. 2. Tighten the ZIF socket by turning the cam screw clockwise to secure the microprocessor module to the system board. 3. Replace the other computer parts you removed earlier in this procedure. 4. Update the BIOS using a flash BIOS update program floppy disk or CD. For instructions on how to flash the BIOS, see "Flashing the BIOS." Back to Contents Page NOTICE: Ensure that the cam lock is in the fully open position before seating the microprocessor module. Seating the microprocessor module properly in the ZIF socket does not require force. NOTICE: A microprocessor module that is not properly seated can result in an intermittent connection or permanent damage to the microprocessor and ZIF socket. NOTE: The pin-1 corner of the microprocessor module has a triangle that aligns with the triangle on the pin-1 corner of the ZIF socket. NOTICE: You must position the microprocessor module correctly in the ZIF socket to avoid permanent damage to the module and the socket. Back to Contents Page Display Assembly and Display Latch Dell™ Inspiron™ 600m Service Manual Display Assembly Display Bezel Display Panel Display Latch Display Assembly 1. Follow the instructions in "Preparing to Work Inside the Computer." 2. Remove the keyboard. 3. Open the display assembly approximately 180 degrees, and support the display assembly so that it does not open past this position. 4. Loosen the captive screw that secures the display cable to the system board, and release the cable from the four cable-routing clips. 5. Pull up on the pull-tab that is attached to the display cable connector to remove the connector from the system board. 6. Remove the three M2.5 x 6-mm screws. 7. Rotate the display assembly to a 90-degree angle, and lift the display assembly up and out of the computer base. CAUTION: Before performing the following procedures, read the safety instructions in your Owner's Manual. NOTICE: To avoid electrostatic discharge, ground yourself by using a wrist grounding strap or by periodically touching an unpainted metal surface (such as the back panel) on the computer. NOTICE: You must remove the display assembly before you remove the palm rest. 1 display 2 cable-routing clips (4) 3 display cable connector 1 display 2 computer base 1 display bumpers (6) 5 top cover 2 M2 x 5-mm screws (6) 6 M2 x 5-mm screws (4) 3 display bezel 7 flex cable connector 4 display panel 8 flex-cable retention bracket Display Bezel 1. Follow the instructions in "Preparing to Work Inside the Computer." 2. Remove the keyboard. 3. Remove the display assembly. 4. Use a plastic scribe to pry the six display bumpers out of the screw holes located on the front of the bezel. 5. Remove the six M2 x 5-mm screws located on the front of the bezel. 6. Starting at the bottom of the display panel (by the Dell™ logo), use your fingers to separate the bezel from the top cover by lifting the inside edge of the bezel away from the top cover. Display Panel 1. Follow the instructions in "Preparing to Work Inside the Computer." 2. Remove the keyboard. 3. Remove the display bezel. 4. Remove the two M2 x 5-mm screws from each side of the display panel. 5. Unsnap the cable from the top cover hook, and lift the bracket out of the display assembly. 6. Lift the display panel, and rotate the display panel out of the top cover. 7. Use the pull-tab to disconnect the bottom flex-cable connector from the inverter connector. 8. Press in both sides of the top display cable connector, and pull the display cable connector away from the top flex-cable connector. CAUTION: Before performing the following procedures, read the safety instructions in your Owner's Manual. NOTICE: To avoid electrostatic discharge, ground yourself by using a wrist grounding strap or by periodically touching an unpainted metal surface (such as the back panel) on the computer. NOTICE: Carefully separate the bezel from the top cover to avoid damage to the bezel. CAUTION: Before performing the following procedures, read the safety instructions in your Owner's Manual. NOTICE: To avoid electrostatic discharge, ground yourself by using a wrist grounding strap or by touching an unpainted metal surface on the computer. 1 top flex-cable connector 2 top display-cable connector 3 pull-tab on bottom flexcable connector Display Latch 1. Remove the keyboard. 2. Remove the display assembly. 3. Remove the display bezel. 4. Remove the three M2.5 x 4-mm screws that secure the display latch bracket to the top cover. 5. Lift the display bracket out of the top cover, and then remove the display latch. Back to Contents Page NOTICE: Disconnect the computer and any attached devices from electrical outlets, and...