Votos - 0, Puntuación media: 0
(
)
)
|
Otros manuales para este modelo:
Resumen del manual
NOTICE: You must position the microprocessor module correctly in the ZIF socket to avoid permanent damage to the module and the socket. Back to Contents Page Display Assembly and Display Latch Dell™ Latitude™ D600 Service Manual Display Assembly Display Bezel Display Panel Display Latch Display Assembly 1. Follow the instructions in "Preparing to Work Inside the Computer." 2. Remove the keyboard. 3. Open the display assembly approximately 180 degrees, and support the display assembly so that it does not open past this position. 4. Loosen the captive screw that secures the display cable to the system board, and release the cable from the four cable-routing clips. CAUTION: Before performing the following procedures, read the safety instructions in your System Information Guide. NOTICE: To avoid electrostatic discharge, ground yourself by using a wrist grounding strap or by periodically touching an unpainted metal surface (such as the back panel) on the computer. NOTICE: You must remove the display assembly before you remove the palm rest. 1 M2.5 x 6-mm screws (3) 057HW 2 display cable connector 3 display 4 computer base 5 pull-tab 6 connector 5. Pull up on the pull-tab that is attached to the display cable connector to remove the connector from the system board. 6. Remove the three M2.5 x 6-mm screws. 7. Rotate the display assembly to a 90-degree angle, and lift the display assembly up and out of the computer base. 1 display 2 cable-routing clips (4) 3 display cable connector 1 display 2 computer base Display Bezel 1. Follow the instructions in "Preparing to Work Inside the Computer." 2. Remove the keyboard. 3. Remove the display assembly. 4. Use a plastic scribe to pry the six display bumpers out of the screw holes located on the front of the bezel. 5. Remove the six M2 x 5-mm screws located on the front of the bezel. 6. Starting at the bottom of the display panel (by the Dell™ logo), use your fingers to separate the bezel from the top cover by lifting the inside edge of the bezel away from the top cover. Display Panel 1 display bumpers (6) 6R933 5 top cover 8M669 2 M2 x 5-mm screws (6) 1428U 6 flex-cable retention bracket 4270E 3 display bezel 6M873 7 flex cable 6M871 4 display panel See MINI RSL 8 M2 x 5-mm screws (4) CAUTION: Before performing the following procedures, read the safety instructions in your System Information Guide. NOTICE: To avoid electrostatic discharge, ground yourself by using a wrist grounding strap or by periodically touching an unpainted metal surface (such as the back panel) on the computer. NOTICE: Carefully separate the bezel from the top cover to avoid damage to the bezel. 1. Follow the instructions in "Preparing to Work Inside the Computer." 2. Remove the keyboard. 3. Remove the display bezel. 4. Remove the two M2 x 3-mm screws from each side of the display panel, and remove the display side brackets. 5. Remove the two M2 x 5-mm screws from each side of the display panel. 6. Unsnap the cable from the top cover hook, and lift the bracket out of the display assembly. 7. Lift the display panel, and rotate the display panel out of the top cover. 8. Use the pull-tab to disconnect the bottom flex-cable connector from the inverter connector. CAUTION: Before performing the following procedures, read the safety instructions in your System Information Guide. NOTICE: To avoid electrostatic discharge, ground yourself by using a wrist grounding strap or by touching an unpainted metal surface on the computer. NOTE: When you replace the display side brackets, ensure that the tabs on the brackets are facing up. 1 display panel See MINI RSL 2 display side brackets (2) 8T145 3 M2 x 3-mm screws (4) 4270E 1 top flex-cable connector 6M871 (flex cable, flex-cable connector, 9. Press in both sides of the top display cable connector, and pull the display cable connector away from the top flex-cable connector. Display Latch 1. Remove the keyboard. 2. Remove the display assembly. 3. Remove the display bezel. 4. Remove the two M2.5 x 4-mm screws that secure the display latch bracket to the top cover. 5. Lift the display bracket out of the top cover, and then remove the display latch. Back to Contents Page and pull-tab) 2 top display-cable connector 3 pull-tab on bottom flex-cable connector NOTICE: Disconnect the computer and any attached devices from electrical outlets, and remove any installed batteries. NOTICE: To avoid electrostatic discharge, ground yourself by using a wrist grounding strap or by touching an unpainted metal surface on the computer. 1 top cover 8M669 2 M2.5 x 4-mm screws (2) 6240E 3 display latch bracket Back to Contents Page Docking Doors Dell™ Latitude™ D600 Service Manual Removing the Docking Doors 1. Follow the instructions in "Preparing to Work Inside the Computer." 2. Gently bend the docking covers and lift them away from the computer base. Installing the Docking Doors Slide the side of the docking covers with the spring over the longer posts. CAUTION: Before working inside your...