Votos - 0, Puntuación media: 0
(
)
)
|
Otros manuales para este modelo:
Resumen del manual
A00 Troubleshooting Working on Your Computer Base Assembly Hinge Covers Hard Drive WLAN/WiMax Card WWAN Card WPAN (UWB/BT) Card FCM Fan Processor Heatsink Assembly Processor Module Memory Coin-Cell Battery Modular Drive LED Cover Keyboard Modem Right Speaker Grill/Fingerprint Reader Assembly Palm Rest Assembly Card Cage 1394 Card RJ-11 Modem Connector System Board Assembly I/O Card DC Power Cable Battery Latch Assembly Display Assembly Flashing the BIOS NOTE: A NOTE indicates important information that helps you make better use of your computer. NOTICE: A NOTICE indicates either potential damage to hardware or loss of data and tells you how to avoid the problem. CAUTION: A CAUTION indicates potential for property damage, personal injury, or death. Back to Contents Page 1394 Card Dell™ Latitude™ E6400 and E6400 ATG and Mobile Workstation Precision™ M2400 Service Manual Removing the 1394 Card Replacing the 1394 Card Removing the 1394 Card 1. Follow the instructions in Before Working on Your Computer. 2. Remove the bottom of the base assembly (see Removing the Bottom of the Base Assembly). 3. Remove the modular drive (see Removing the Modular Drive). 4. Remove the hinge covers (see Removing the Hinge Covers). 5. Remove the heatsink assembly (see Removing the Processor Heatsink Assembly). 6. Remove the display assembly (see Removing the Display Assembly (E6400 and M2400) or Removing the Display Assembly (E6400 ATG)). 7. Remove the LED cover (see Removing the LED Cover). 8. Remove the keyboard (see Removing the Keyboard). 9. Remove the right speaker grill (see Removing the Right Speaker Grill/Fingerprint Reader Assembly). 10. Remove the palm rest assembly (Removing the Palm Rest Assembly). 11. Remove the card cage (see Removing the Card Cage). 12. Disconnect the 1394 cable from the system board, and unroute the cable. 13. Remove the two M2 x 3 screws. 14. Lift the 1394 card up at an angle and remove it. CAUTION: Before you begin the following procedure, follow the safety instructions that shipped with your computer. 1 1394 cable connector 2 system board 3 M2 x 3 screws (2) 4 1394 card Replacing the 1394 Card 1. Insert the 1394 card at a 45-degree angle to fit the connector into the base assembly. Use the alignment pins to seat into position. 2. Replace the two M2 x 3 screws. 3. Route and connect the 1394 cable to the system board. 4. Replace the card cage (see Replacing the Card Cage). 5. Replace the palm rest assembly (Replacing the Palm Rest Assembly). 6. Replace the right speaker grill (see Replacing the Right Speaker Grill/Fingerprint Reader Assembly). 7. Replace the keyboard (see Replacing the Keyboard). 8. Replace the LED cover (see Replacing the LED Cover). 9. Replace the display assembly (see Replacing the Display Assembly (E6400 and M2400) or Replacing the Display Assembly (E6400 ATG)). 10. Replace the heatsink assembly (see Replacing the Processor Heatsink Assembly). 11. Replace the hinge covers (see Replacing the Hinge Covers). 12. Replace the modular drive (see Replacing the Modular Drive). 13. Replace the bottom of the base assembly (see Replacing the Bottom of the Base Assembly). 14. Follow the procedures in After Working on Your Computer. Back to Contents Page CAUTION: Before you begin the following procedure, follow the safety instructions that shipped with your computer. Back to Contents Page Base Assembly Dell™ Latitude™ E6400 and E6400 ATG and Mobile Workstation Precision™ M2400 Service Manual Removing the Bottom of the Base Assembly Replacing the Bottom of the Base Assembly Removing the Base Assembly Replacing the Base Assembly Removing the Bottom of the Base Assembly 1. Follow the procedures in Before Working on Your Computer. 2. Close the display and turn the computer upside down. 3. Loosen the captive screw. 4. Slide the bottom of the base assembly away from the hinge covers, and lift to remove the bottom of the base assembly. Replacing the Bottom of the Base Assembly 1. Slide the bottom of the base assembly into place. 2. Tighten the captive screw. 3. Follow the procedures in After Working on Your Computer. Removing the Base Assembly 1. Follow the procedures in Before Working on Your Computer. 2. Remove the bottom of the base assembly (see Removing the Bottom of the Base Assembly). 3. Remove the card in the WWAN/FCM card slot, if present (see Removing a WWAN Card or Removing an FCM from the WWAN/FCM Slot). 4. Remove the card from the WLAN/WiMax card slot, if present (see Removing the WLAN/WiMax Card). CAUTION: Before you begin any of the procedures in this section, follow the safety instructions that shipped with your computer. 1 hinges covers (2) 2 bottom of the base assembly 3 captive screw 5. Remove the hinge covers (see Removing the Hinge Covers). 6. Remove the card from the WPAN/UWB/FCM card slot, if present (see Removing a WPAN (UWB/BT) Card or Removing an FCM from the WPAN/UWB/FCM Slot). 7. Remove the heatsink assembly (see Removing the Processor Heatsink Assembly). 8. Remove the h...