Votos - 3, Puntuación media: 3.3
(
)
)
|
Resumen del manual
113604-4 American Dryer Corporation 88 Currant Road Fall River MA 02720-4781 USA Telephone: +1 (508) 678-9000 / Fax: +1 (508) 678-9447 e-mail: techsupport@amdry.com Retain This Manual In A Safe Place For Future Reference Please read this manual carefully to thoroughly familiarize yourself with the Phase 8 microprocessor controller (computer) system features, operational instructions, and programming characteristics. This manual contains important information on how to employ all the features of your new dryer in the safest and most economical way. This product embodies advanced concepts in engineering, design, and safety. If this product is properly maintained, it will provide many years of safe, efficient, and trouble free operation. We have tried to make this manual as complete as possible and hope you will find it useful. The manufacturer reserves the right to make changes from time to time, without notice or obligation, in prices, specifications, colors, and material, and to change or discontinue models. “IMPORTANT NOTE TO PURCHASER” Information must be obtained from your local gas supplier on the instructions to be followed if the user smells gas. These instructions must be posted in a prominent location near the dryer. WARNING! Proposition 65 Use of this product could expose you to substances from fuel combustion that contain chemicals known to the State of California to cause cancer, birth defects and other reproductive harm. Table of Contents____________ General User Information Coin/Debit Models “Coin Dry Mode”.....3 General User Information Non-Coin Models “OPL Dry Mode” .......3 Introduction to Programming...............4 Quick Reference Programming Menu for Coin/Debit/Free Models....................5 Quick Reference Programming Menu for Non-Coin (OPL) Models ...................6 Coin Programming Example Changing “Time for Amount to Start” ..................7 Programming Non-Coin (OPL) Cycles ..7 Non-Coin (OPL) Factory Preset Programs/Parameters ...........................8 Programming Selections.......................9 Faults ....................................................13 Events...................................................13 NOTES _____________________________________________________________________________________________________________________________ 2 American Dryer Corp. 113604 -4 Important ! Read all instructions before operating! General User Information Coin/Debit Models “Coin Dry Mode” ___ Cold Start (Initial/First Use) Appliance is programmed at the factory as follows: Dryer 10 minute dry time/quarter (coin 1) $.25 dry price Warm Start (After Power Failure) A few seconds after power is restored, if a cycle was in progress at the time of the power failure, the display will prompt “Select Cycle to Restart”. This is to indicate the need for a setting to be pressed to restart dryer. Pricing After the door is opened following the completion of a cycle, the display indicates the cycle price (unless set for free operation). As coins or debit inputs arrive, the display will change to lead the user through the initiation of a cycle. There are 2 types of pricing: Accumulative Time In this Vending Mode each coin inserted has a specific value in time, which is determined by the “Time for Amount to Start”. Accumulative Coin In this Vending Mode additional time can only be achieved when the “Time for Top Off” has been inserted. Note ! A maximum of 99 minutes may be purchased; no additional credit is given when 99 minutes is in the display. “Free Dry Mode” When the Dry Mode is set to FREE, only one cycle time is initially vended. Pressing and holding the HIGH or LOW key for 3-seconds will allow the time to be adjusted. Pressing HIGH will increase the time in 1 minute units and pressing LOW will decrease the time in 1 minute units. Once the desired time is chosen, pressing MED will save the new time. Hot Keys Display Reason S.A.F.E. is Disabled While machine is idle displaying “S.A.F.E. DISABLED … READY INSERT 25. TO START” or “S.A.F.E. DISABLED … SELECT A CYCLE”, press the PAUSE and LO keys simultaneously. Clear Credit While machine is idle displaying “SELECT A CYCLE” press and hold PAUSE, while holding PAUSE press HI, HI, HI, LO, LO, MED within 3-seconds and the control will display “CLEAR CREDIT?” While still holding PAUSE press any key to clear credit. Releasing PAUSE then pressing any key will not clear credit. Display Fault Message While machine is displaying “OUT OF ORDER” press the LO key. Display Credit Remaining While machine is displaying “OUT OF ORDER” press the HI key. Clear “Out of Order” While machine is displaying “OUT OF ORDER” press and hold the PAUSE key for 3-seconds. General User Information Non-Coin Models “OPL Dry Mode” ____ Cold Start (Initial/First Use) This appliance has 20 preset cycles, which are ready for use. To start the unit, use the UP and DOWN ARROW keys to scroll through the preset cycles, until the desired cycle is highlighted, then pre...
Otros modelos de este manual:Notebooks - Microprocessor 8.4 Rev 2.2 (664.01 kb)