Votos - 3, Puntuación media: 4
(
)
)
|
Resumen del manual
• If wires are removed or replaced make sure wiring and wire harness are properly routed and secured. Failure to properly route and secure wiring could result in vehicle malfunction, property damage, personal injury, or death. • Lift only one end of the vehicle at a time. Use a suitable lifting device (chain hoist or hydraulic floorjack) with 1000 lb. (454 kg) minimum lifting capacity. Do not use lifting device to hold vehicle in raisedposition. Use approved jack stands of proper weight capacity to support the vehicle and chockthe wheels that remain on the floor. When not performing a test or service procedure that requiresmovement of the wheels, lock the brakes. PERIODIC SERVICE SCHEDULE See General Warnings on page 9. WARNING • Service, repairs, and adjustments must be made per instructions in the appropriate maintenanceand service manual. • If any problems are found during scheduled inspection or service, do not operate vehicle until repairsare made. Failure to make necessary repairs could result in fire, property damage, severe personalinjury, or death. NOTE: If the vehicle is constantly subjected to heavy use or severe operating conditions, these preventive maintenance procedures should be performed more often than recommended in the Periodic Service and Lubrication Schedules. Both the Periodic Service Schedule and the Periodic Lubrication Schedule must be followed to keep vehicle in optimum operating condition. 2008 HUV 4213-G and HUV 4213-GXP Owner’s Manual Page 27 Periodic Service Schedule PERIODIC SERVICE SCHEDULE REGULAR INTERVAL SERVICE Daily service by owner Pre-Operation and Daily Safety Checklist See Pre-Operation and Daily Safety Checklist on page 17. Performance Inspection See Performance Inspection on page 17. Monthly service by owner or trained technician Engine Check engine oil level; change as required. See Periodic Lubrication Schedule on page 29. Check engine cooling air intake; visually inspect unshrouded area around engine exhaust for grass and debris and clean if necessary. Tires Check air pressure and adjust if necessary. See Vehicle Specifications on page 40. General vehicle Wash engine compartment and underside of vehicle. Do not wash engine when hot. Semiannual service by trained technician only (or every 50 hours of operation, whichever comes first) Battery Clean terminals and wash dirt from casing; check electrolyte level. Add distilled water if necessary. See page 36. Front wheel alignment and toe-in Check and adjust if necessary. See Steering and Front Suspension Section in the appropriate maintenance and service manual. Electrical wiring and connections Check for tightness and damage Brake system Inspect master cylinder, wheel cylinders, brake lines, and hoses for damage or leakage. Check park brake cables for damage; replace if necessary. Check brake shoes and drums; replace if necessary. See Wheel Brake Assemblies Section in the appropriate maintenance and service manual. Annual service by trained technician only (or every 100 hours of operation, whichever comes first) Engine Check for leaks around gaskets, fill plugs, etc. Inspect, clean and gap spark plug; replace if necessary. Engine air intake system Check air filter element; clean or replace if necessary. Check clamps for tightness; check hose for cracks. General vehicle Check for loose hardware and tighten if necessary. Two year service by trained technician only (or every 200 hours of operation, whichever comes first) Fuel filters Replace. Dispose of used filters properly. See Engine Oil And Filter Change on page 31. Page 28 2008 HUV 4213-G and HUV 4213-GXP Owner’s Manual Periodic Lubrication Schedule PERIODIC LUBRICATION SCHEDULE PERIODIC LUBRICATION SCHEDULE REGULAR INTERVAL SERVICE LUBRICATION POINTS RECOMMENDED LUBRICANT Semiannually by owner or trained technician (or every 50 hours of operation, whichever comes first) Brake pedal shaft bearings 1 Dry Moly Lube (P/N 603 00 00-01) Accelerator push rod pivots, mounts, and shifter cable pivots 2 Dry Moly Lube (P/N 603 00 00-01) Front suspension (2 fittings) Chassis Lube (EP NLGI Grade 2) Annually by trained technician only (or every 100 hours of operation, whichever comes first) Check/fill transaxle to plug level 29 oz. (.85 liters) 80-90 Wt. API Class GL-3 or 80-90 Wt. AGMA Class 5 EP gear lubricant Inspect front wheel bearings (Repack as necessary) Chassis Lube (EP NLGI Grade 2) First change 100 hours – additional change every 200 hours of operation or annually, whichever comes first Change engine oil and oil filter 32 oz. (0.95 liter) without filter; 38 oz. (1.12 liters) with filter. See Oil Viscosity on page 34. 2416223535221 167 Figure 15 Lubrication Points 2008 HUV 4213-G and HUV 4213-GXP Owner’s Manual Page 29 Master Cylinder MASTER CYLINDER 1231.FullLevel2.SafeLevel3.LowLevel Figure 16 Brake Fluid Reservoir The master cylinder is located under the passenger seat toward the center of the vehicle (Figure 16). Raise or remove the seat to check the brake fluid...
Otros modelos de este manual:Equipo para la TC - HUV 4213-GXP (1.98 mb)