Votos - 3, Puntuación media: 4
(
)
)
|
Resumen del manual
Do not climb on the mast. Tip-over Hazards Do not raise the load unless the stabilizers (if equipped) and legs have been fully lowered and locked and the casters are in full contact with the ground. Do not raise the load unless the leg retainer pins are properly inserted through the leg and the base. Do not remove the leg retainer pins while the machine is loaded and/or raised. Do not raise the load unless the machine is on a firm, level surface. Do not raise the load unless the load handling attachment is properly secured to the machine. Do not use blocks to level the machine. Do not move the machine with a raised load, except for minor positioning. Do not operate the machine in strong or gusty winds. Increasing the load surface area will decrease machine stability in windy conditions. Do not leave a load raised when windy conditions may occur unless the machine(s) are properly guy- wired. Do not cause a horizontal force or side load to the machine by raising or lowering a fixed or overhanging load. Prior to use, check the work area for drop-offs, holes, bumps, debris, unstable or slippery surfaces or other possible hazardous conditions. Genie Superlift Advantage PartNo.97550 Third Edition • Third Printing Operator's Manual Do not place ladders or scaffolding against any part of the machine. Do not use the machine on a moving or mobile surface or vehicle. Do not exceed the rated load capacity. See Load Capacity Charts section. Avoid debris and uneven surfaces while rolling a Genie Superlift with the legs folded up. Do not replace machine parts critical to stability or structure with items of different weight or specification. Do not use a straddle base or the flat forks on an SLA-20 or an SLA-25. Lifting Hazards Use proper lifting techniques to load or tip the machine. Use proper lifting techniques when installing or removing the load handling attachments. SAFETY RULES Electrocution Hazards This machine is not electrically insulated and will not provide protection from contact with or proximity to electrical current. Keep away from the machine if it contacts energized power lines. Personnel must not touch or operate the machine until power lines are shut off. Maintain safe distances away from electrical power lines and apparatus in accordance with applicable governmental regulations and the following chart. Voltage Minimum Safe Approach Distance Phase to Phase Feet Meters 0 to 300V Avoid Contact 300V to 50KV 10 3.1 50KV to 200KV 15 4.6 200KV to 350KV 20 6.1 350KV to 500KV 25 7.6 500KV to 750KV 35 10.7 750KV to 1000KV 45 13.7 Allow for mast movement and electrical line sway or sag, and be aware of strong or gusty winds. Do not use the machine as a ground for welding. Bodily Injury Hazard Do not grasp the cable. PartNo.97550 Genie Superlift Advantage Operator's Manual Third Edition • Third Printing SAFETY RULES Crushing Hazards Do not raise if the load is not properly centered on the load handling attachment. Do not raise unless the load is properly secured to the load handling attachment. Do not stand under or allow personnel under the machine when the load is raised. Do not stand under the load. The safety brake system (if equipped) will allow the load to drop 1 to 3 feet / 30 to 92 cm before locking the columns. Do not lower the load unless the area below is clear of personnel and obstructions. Keep hands and fingers away from folding legs and other potential pinch points. Maintain a firm grasp on the stabilizer when the lock plates are released. The stabilizer will drop. Maintain a firm grasp on the leg when the retaining pin is removed. The leg will drop. Maintain a firm grasp on the winch handles until the brake is locked. The brake is locked when the load will not cause the winch handles to turn. Adjustable Flat Forks Do not raise the load unless the snap pins are properly inserted in the forks. Fork Extensions Do not raise the load unless the fork extensions are properly secured to the forks. Collision Hazards Check the work area for overhead obstructions or other possible hazards. Do not tilt the machine back unless the area is clear of personnel and obstructions. Use common sense and planning when transporting the machine on an incline or slope. Do not load for transport unless the machine and vehicle are on a level surface. Use proper lifting techniques to load the machine. Genie Superlift Advantage PartNo.97550 Third Edition • Third Printing Operator's Manual Damaged Machine Hazards Do not use a damaged or malfunctioning machine. Do not use a machine with a worn, frayed, kinked or damaged cable. Do not use a machine with less than 4 wraps of cable on the winch drum when the carriage is fully lowered. Conduct a thorough pre-operation inspection prior to each use. Be sure all decals are in place and legible. See Decals section. Be sure that the operator's manual is complete, legible and in the storage container located on the machine. Maintain proper lubrication on the winch. See Genie Superlift Pa...