Votos - 4, Puntuación media: 4
(
)
)
|
Resumen del manual
Plug power tool into the power to platform GFCI outlet. To resume machine functions, move generator toggle switch to machine functions position. All functions will operate. Engine Idle Select (rpm) Select engine idle (rpm) using the symbols on the control panel. · Rabbit and foot switch symbol: foot switch activated high idle · Turtle symbol: low idle · Rabbit symbol: high idle Check Engine Light (if equipped) Light on and engine stopped: Tag the machine and remove from service. Light on and engine still running: Contact service personnel within 24 hours. Stopping the Engine Push in the red Emergency Stop button and turn the key switch to the OFF position. After Each Use 1 Select a safe parking location—firm level surface, clear of obstruction and traffic. 2 Retract and lower the boom to the stowed position. 3 Rotate the turntable so that the boom is between the non-steering wheels. 4 Turn the key switch to the OFF position and remove the key to secure from unauthorized use. 5 Chock the wheels. Genie S-80 & Genie S-85 PartNo.43650 Second Edition · Fifth Printing Operator's Manual Transport Instructions Observe and Obey: Transport vehicle must be parked on a level surface. Transport vehicle must be secured to prevent rolling while machine is being loaded. Be sure vehicle capacity, loading surfaces and straps or lines are sufficient to withstand machine weight. See Specifications section. Securing to Truck or Trailer for Transit Always use the turntable rotation lock pin each time the machine is transported. Always chock machine wheels in preparation for transport. Use tie points on drive chassis for anchoring down to transport surface. Use lower platform mount between boom end and platform to secure boom from side-to-side movement. Do not use excessive downward force when securing boom section. Use chains or straps of ample load capacity. Turn key switch to the OFF position and remove key before transporting. Inspect entire machine for loose or unsecured items. Free-wheel Configuration for Winching Chock wheels to prevent machine from rolling. 2WD models: Release non-steer wheel brakes by turning over torque hub disconnect caps (see below). 4WD models: Release wheel brakes by turning over all four torque hub disconnect caps (see below). Be sure winch line is properly secured to drive chassis tie points and path is clear of all obstructions. Reverse procedures described to re-engage brakes. Note: The pump free-wheel valve should always remain closed. Disengage Position Engage Position PartNo.43650 Genie S-80 & Genie S-85 Operator's Manual Second Edition· Fifth Printing Decal Inspection Use the pictures on the next page to verify that all decals are legible and in place. Below is a numerical list with quantities and descriptions. Part No. Decal Description Quantity 25994 Caution - Component Damage Hazard 1 27204 Arrow - Blue 1 27205 Arrow - Yellow 1 27206 Triangle- Blue 2 27207 Triangle - Yellow 2 27564 Danger - Electrocution Hazard 3 28157 Label - Dexron 1 28158 Label - Unleaded 2 28159 Label - Diesel 2 28160 Label - Liquid Petroleum Gas 1 28161 Danger - Crushing Hazard 4 28163 Notice - Maximum Side Force - 150 lbs 1 28164 Notice - Hazardous Materials 1 28165 Notice - Foot Switch 1 28171 Label - No Smoking 2 28174 Label - Power to Platform, 230V 2 28175 Caution - Compartment Access 1 28176 Notice - Missing Manuals 1 28177 Warning - Platform Rotate 2 28181 Warning - No Step or Ride 1 28235 Label - Power to Platform, 115V 2 28236 Warning - Failure To Read . . . 1 30080* Notice - Maximum Load 500 lbs 1 31060 Danger - Tip-over Hazard, Interlock 1 32700 Danger - Safety Rules 2 32726 Label - Glow Plug (option) 1 32728 Label - Generator (option) 1 32932 Danger - Tip Over- Axles 2 Decals Part No. Decal Description Quantity 32933 Serial Plate - S-80 32996 Notice - Axle Extension Operation 32997 Warning - Hand and Foot 32998* Notice -Maximum Load 600 lbs 32999 Notice - Tire Pressure 33463 Serial Plate - S-85 33550 Safety Tape — 33952 Danger - Tilt-Alarm 33956 Notice - Ford Engine Specs-Ford LRG 33986 Notice - Deutz Diesel Engine Specs 35599 Notice - Align Air Hoses 40434 Label - Lanyard Anchorage 43594* Notice -Maximum Load 750 lbs 43595 Danger - Tip-over, Tires 43649 Ground Control Panel 43647 Notice - Operating Instructions 43663 Notice - Function Enable 49741 Notice - Ford Engine Specs-LRG-425 EFI 1 44769 Lift/Drive Select (option) 44981 Airline to Platform 44986 Notice - Maximum Manual Force - 90 lbs 1 49926 Ground Control Panel 52156 Platform Control Panel 52966 Cosmetic - 4 x 2 52967 Cosmetic - 4 x 4 52972 CE Mark 62920 Cosmetic - Genie S-80 62921 Cosmetic - S-80 62922 Cosmetic - Genie S-85 62923 Cosmetic - S-85 72160 Ground Control Panel 72162 Platform Control Panel *Please reference the Specifications section or the chart on page 2 to determine the capacity of your machine. Genie S-80 & Genie S-85 PartNo.43650 Second Edition · Fifth Printing Operator's Manual DECALS Ground Controls Side Engine Side Shading indi...
Otros modelos de este manual:Equipo para la TC - 43650 (1.5 mb)
Equipo para la TC - S-80 (1.5 mb)