Votos - 4, Puntuación media: 4
(
)
)
|
Resumen del manual
The farther forward the left control is moved, the faster the right turn will be made. See Figure 3–16. 2139 Figure 3–16 Right Hand Turn in Reverse Move the right hand control lever farther backwards than the left control lever. The farther forward the right control is moved, the faster the left turn will be made. See Figure 3–17. 2140 Figure 3–17 Left Hand Turn in Reverse Pre-Start Inspection and Operation Spin Turn Make sure to use the machine hand holds while doing a spin turn to maintain your balance. CAUTION Move the travel control levers in opposite directions to spin the machine on it axis. To spin left, move the right control lever forward while pulling the left control lever backwards; to spin turn to the right, push the left control lever forwards and while pulling the right control lever backwards. Figure 3–18. 2141 Figure 3–18 Spin Turn Fifth Proof Pre-Start Inspection and Operation Attachment Installation and Removal Attachment Lock Pins The mounting plate located at the front of the machine provides for the easy installation and safe use of the wide variety of available attachments. This system is very easy to use, but requires the proper use of the attachment lock pins. There are two positions for the attachment lock pins, the unlocked position and the locked position. Once the machine has picked up an attachment, shut off the engine and rotate the attachment locks into the “locked” position (Item 1, Figure 3–19). As you rotate the lock pin, it will drop downwards, securing the attachment to the machine. If the lock pin does not drop into the locked position, start the engine and either raise or lower the attachment slightly until the lock pins snap into place. 112022 Pins Locked Figure 3–19 Attachment Locks in Locked Position CAUTION Until the attachment lock pins are fully in the locked position, the attachment has not been safely secured to the machine. Do not stand near the attachment until it is fully secured to the machine. To release an attachment, rotate the attachment locks to the “unlocked” position (Item 1, Figure 3–20). The lock pins will automatically rise, releasing the attachment from the machine. If the pins do not release the attachment or are very hard to rotate, start the engine and tilt the attachment slightly forwards or backwards until the pins can be rotated. Fifth Proof Pre-Start Inspection and Operation CAUTION Make sure to keep your hands and feet away from the attachment during the unlocking process. As the attachment becomes free from the machine, it may move. 11PinsUnlocked2021 Figure 3–20 Attachment Locks in Unlocked Position Installation of Non-Hydraulically Powered Attachments There are many available attachments that are very easy to install. To install any of the non- hydraulically powered attachments: 1. Position the attachment on a level surface. NOTE: Clean the inside lower edge of the female attachment mounting plate to remove any debris that might interfere with the attachment installation. 2. Start the machines engine, lower the loader arm and tilt the mounting plate forwards. NOTE: Make sure that both of the attachment lock pins (Item 1, Figure 3–20) are in the “unlocked” position. See Attachment Lock Pins earlier in this section. 3. Slowly drive towards the attachment and align the top edge of the male mounting plate (Item 1, Figure 3–21) and the upper lip of the female attachment mounting plate (Item 2, Figure 3–21). Tuck the upper edge of the male mounting plate into the upper lip of the female attachment mounting plate. 1 2 2020 Figure 3–21 Non-powered Attachment Installation Fifth Proof Pre-Start Inspection and Operation 4. When the machines mounting plates top edge is seated in the attachment mounting plate, curl the machines mounting plate backwards slightly to allow the lower edge of the machines mounting plate to slide into position. See Figure 3–22. 12029 Figure 3–22 Attachment Installed 5. Shut the engine off. 6. Rotate the attachment lock pins (Item 1, Figure 3–22 and Item 1, Figure 3–23) into the locked position, securing the attachment to the machine. 112022 Pins Locked Figure 3–23 Attachment Locks in Locked Position 7. Test the security of the attachment connection by fully lowering with loader arm and tilting the attachment downwards until the front tires slightly lift off the ground. Fifth Proof Pre-Start Inspection and Operation Removal of Attachment 1. Lower the attachment onto a firm, level surface. 2. Shut off the machine engine. 3. Rotate the attachment lock pins to the UNLOCKED position (Item 1, Figure 3–24). 11PinsUnlocked2021 Figure 3–24 Attachment Locks in Unlocked Position 4. Start the engine and rotate the mounting plate downwards. 5. Back away from the attachment. NOTE: It may be necessary to lower the loader arm assembly slightly to fully disengage from the attachment. Installation of Hydraulically Powered Attachments There are many hydraulically powered attachments available that are very easy to install. To install any o...
Otros modelos de este manual:Equipo para la TC - BOXER 427 (2.94 mb)