Votos - , Puntuación media:
(
)
)
Fabricar: ATN
Tamaño del archivo: 194.42 kb
Nombre del archivo: 95c62937-8930-4ba7-ae61-a08a451e6017.pdf
Idioma del manual:
El documento se está cargando, por favor, espere
 |
El documento se está cargando, por favor, espere
Resumen del manual
• Make sure that the green luminance of the light intensifier tube is present. • Observe the scene, and adjust the diopter and/or lens for optimal image clarity. • You may now enter a dark environment or simply shut the lights off in order to darken the room. • Next, remove the lens cap/daylight filter. • Observe the scene, and adjust the front lens for ideal focus. • Finally, you may want to turn the infra red (IR) illuminator on. Notice the ability of the Aries scope to see in total darkness with the aid of the IR illuminator. Batteryinstallation OPERATING MOUNTING 1. Slightly loosen the horizontal and vertical fixing screws on the 7/8” weaver rail built into the scope. 2. Place the scope on the dovetail mount of the fire arm making certain that the mount aligns with the receptor attachment screw groove. Adjust as necessary. 3. Tighten the horizontal fixing screws. NOTE: Receptor attachment screws may need to be tightened after continuous shooting. MOUNTING SYSTEM The ATN Night Vision Riflescopes Mounting System allows to change the position of the riflescope flexibly on the weapon in relation to a shooter in combination with the fixed positions already available on the weaver rail. For this purpose in the base of the mounting bracket there is a rail with a fixing projection. There are three grooves in the mounting bracket for mounting this rail. Besides it is possible to change the position of the rifle- scope additionally by 1/3 of inch. For doing this one needs to about-face the rail. WeaverrailGroovesRailwithafixingprojectionScrews To change the position of the riflescope on the weaver rail additionally follow the steps mentioned below: 1. Unscrew the two screws, which attach the rail to the mounting bracket. 2. Take the rail out of the groove. 3. About-face the rail in case of necessity. 4. Place the rail into another groove. 5. Fix the rail with the two screws. NOTE: If the rail is not taken out easily, screw up tight one of screws into the threaded aperture in the middle of a fixing projection of the rail. Continue rotation of the screw. Thus the screw will push out a rail from a groove. BRIGHTNESS ADJUSTMENT By rotating the “R” handle you may adjust the reticle’s brightness. Adjustment could be easily seen if you look trought the scope while adjustement. ReticleBrightnessAdjustment(MK6900) ReticleBrightnessAdjustment(MK390) WINDAGE AND ELEVATION The vertical and horizontal adjustments for the Aries can be achieved by turning the elevation and windage adjustment mechanisms (remove dust caps first). Each click equals to 1/8 inches at 100 yards. When reaching the maximum of rotation do not use force. WindageElevation FOCUSING To focus your riflescope you will need to adjust the diopter first thing. Simply turn the diopter clockwise until it stops. Then, while looking through the diopter at a subject, slowly turn the diopter back counter clockwise until the grain in the image is sharp. NOTE: We suggest that you focus the diopter during daylight with the filter on. Next, focus the front lens until the image and the grain are both sharp. When you are in the low-light conditions and the daylight filter is off you may focus the front lens to receive a sharp image, the diopter should not be adjusted. NOTE: The front lens should be readjusted as you view objects at different distances. IR ILLUMINATOR Infra-red (IR) Illuminators are common for night vision technology. The IR light greatly enhances the performance of your Aries scope, while remaining almost totally invisible to the naked eye. In dark environment, power up the Aries scope. Now, find a scene and examine it without the IR on then with IR powered up. Note the difference in illumination. It is important to remember that the IR illuminator is simply an infra red light source, and like any light source it may loose its effectiveness over a great distance. To fix the IR Illuminator to the riflescope screw the thumb screw on the IR into the thread on the scope. To switch the IR on and to adjust the brightness rotate the rheostat located on the side of the Illuminator. The changes of adjustment could be observed while looking through the scope. The IR is off when the mark on the rheostat coincides with “0” on the scale. IR Brightness NOTE: The riflescope could be equipped with digitally controlled IR. The IR illuminator control buttons are located on its side. To switch the Digital IR illuminator on/off press “+” and “-” buttons simultaneously. When the IR illuminator is switched on you can see the green LED lit. By pushing the buttons “+” and “-” you may adjust the IR brightness. The IR beam is focusable to change the field of coverage. To change the beam width slightly turn the IR lens. You could change the IR control panel fitting your needs. The screw-tool included into the set should be used for weakening the fixing screw located on the IR. Rotate the IR placing at in the most convenient position. Tighten the screw with the screw-tool to fix the n...