Votos - 4, Puntuación media: 4.5 ( )

Fabricar: Danby Tamaño del archivo: 177.13 kb Nombre del archivo: Idioma del manual:

NOTE: The LED readout is programmed to default to display the ambient relative humidity conditions. To view the Set Operating Relative Humidity Value, press the “up” or “down” button (once) and the set RH operating value will flash for approximately 5 seconds in the LED window, then revert back to display the internal RH value. 2) ON/OFF Button: Each time this button is pressed the unit turns ON (adjacent indicator light illuminates) orOff (adjacent indicator light is not illuminated) 3) CONTINUOUS: Used for Continuous Dehumidifier Operation (unit will run non-stop). NOTE: Humidity values (settings) cannot be programmed in this mode. The adjacent (green) indicatorlight illuminates to signify the “continous” mode iscurrently in operation. 4) HUMIDITY UP: This button allows you to increasethe relative humidity setting. Each time this button is pressed, the RH value setting is increased incrementally by 5% (ranging from 35% - 80%) 5) HUMIDITY DOWN: This button allows you todecrease the relative humidity setting. Each time this button is pressed the RH value setting is decreased incrementally by 5% (ranging from 80% - 35%). 6) HIGH FAN: The adjacent (green) indicator light illuminates when HIGH FAN is selected. 7) LOW FAN: The adjacent (green) indicator light illuminates when LOW FAN is selected. 8) WATER FULL INDICATOR: This (red) light illuminates under the following conditions: A) When the internal water tank is not properly installedinside the cabinet. B) When the internal water tank is full. The water tank must be emptied and replaced back in the cabinetbefore normal operating conditions can resume. INDICATOR LIGHT FUNCTION Power Light (Green): When the unit is first connected to an electrical outlet, the (green) power light will not light until the “on/off” button is pressed. When the “on/off” buttonis activated, the power light turns to a state “on” condition. The dehumidifier will automatically default to the factory default setting: Humidity Setting: 60% Fan Speed: High IMPORTANT NOTE: Depending on the humidityconditions of the surrounding environment, the dehumidifier may not start automatically when the“on/off” button is pressed (see dehumidifier operatinginstructions for details). In the event of a power failure, the unit will default to the last programsetting that was used when power is restored. Water Full Indicator Light (Red): When the water tank is full and/or incorrectly positioned inside the cabinet, the (water full) red lightturns on and remains on until such time the tank is emptied and/or correctly re-positioned. This conditionwill result in the immediate shut down of the dehumidifying system (both compressor and fanmotor operation are terminated). This is a safety feature. When the water tank is emptied and/or correctly re-positioned, the dehumidifier will resumeoperation automatically. NOTE: It may takeseveral minutes before operating conditions resume. Memory Setting: Each time the unit is disconnected /re-connected and/or in the event of a power failure, the electronic circuit board automaticallydefaults tothe last program setting that was used. It may takeseveral minutes before operating conditions resume. NOTE: In the event of a power failure, all previous settings are automatically remembered/recalled. When the unit is switched “off” manually (using theon/off keypad) the unit will always default to the last program setting that was used. 4 OPERATING INSTRUCTIONS (cont’d) WATER TANK IMPORTANT: Never tamper with or attempt to defeat the water level (safety) float switch system. Proper installation of the water tank is crucial to maintaining reliable OPERATION dehumidifier operation. The water tank holds accumulated condensed water and by means of a safety switch, controls both the water level and operation of the dehumidification process- i.e. When the water tank is full and/or accidentally displaced inside the cabinet, the float switch actuator (inside the tank) breaks contact with the safety switch. This condition results in the immediate shut down of the compressor and fan motor system, preventing moisture from being condensed. DEHUMIDIFYING is a means of removing moisture from the air. A dehumidifier will help to protect yourhome and valued possessions from damage (swelling) caused by moisture in the air. Essentially a dehumidifier removes moisture from air as moist air passes over a dehumidifying (evaporator) coil. Moisture is condensedon the evaporator coil, drained, and collected inside an internal (removable) water tank located at the front of the unit. The exhausted air being returned into the room environment is elevated several degrees causing thesurrounding air temperature to increase (slightly). This process also contributes to lowering the relative humidity of the surrounding air. DEHUMIDIFYING When the unit is first connected to the electrical outlet, the (green) power light MODE INSTRUCTIONS will not light until the “on/off” button is pressed. When the “on/off” button...

Descargar ahora

Introduzca dos números de la imagen: