Votos - 3, Puntuación media: 4.3
(
)
)
|
Resumen del manual
Remove the original bulb connectors from the bottom side of the housing. 2. Remove the plastic housing from the vehicle. 3. Remove the tail light lens by gently prying the housing away from the lens tabs. 4. Now is a good time to clean the lens and housing. If lenses are in bad shape a new set is recommended. 5. Note that the screws and mounting plates are assembled differently for the driver side set and passenger side set. The LED assemblies will sit in the housing at an angle similar to the back side of the original lens. driver side(screws and mounting plate offset to the left) passenger side(screws and mounting plate offset to the right) 6. Insert each new LED assembly through the hole where the original bulb and connector were located. Use caution when feeding the wires through the socket opening to avoid damaging the wire insulation. 7. Feed the wires through the large hole in the back plate and attach the back plate onto the back side of the housing. The flat side of the mounting plate should be toward the outside and the side with the slight raised center should go in towards the housing. This will align the mount in the original housing. 8. Secure the LED assembly into the housing with the supplied back plate and #6 lock nuts. 9. Place the original lens gasket into place and replace the tail light lens. 10. Cut off the existing light socket as it will not be used. Do not strip the wires. Trim the wires from LED assembly to appropriate length once mounted, making sure wires are routed cleanly and securely. 11. Use the supplied moisture resistant pigtail connectors* to attach the wires from the new LED assembly to the existing vehicle harness. Insert the appropriate wire from vehicle harness and mating LED assembly wire into a connector and crimp following instructions below. *For the best connection, soldering is recommended. But to simplify installation, the supplied connectors will provide a fast weather resistant connection. The correct crimp method for the supplied connectors is: 1.) Insert UNSTRIPPED wires into the connector and ensure they are all they way in by observing the clear bottom of the connector to see the wires are touching the end. 2.) Use pliers to push the blue cap down flush with the edge of the clear body, completing the connection. The connection will only be correct if pressed firmly down with pliers. LED lightVehicle harnessTail lightBrownBrownDriver’s TurnGreenGreenPassenger’s TurnGreenYellowGroundBlackBlack or chassis 12.Repeat forthe otherside. 13.Test the tail lights, brake lights, and turn signals. Ifthe turn signals do notflash you will need to upgrade yourflasher. If you are replacingonly the rearturn signals you should be able to use a heavy duty electronicflasherfrom your local parts store. If you are replacing both frontand rear or do nothave front bulbs you will need a no-loadflasher,Dakota Digital part numberLAT-NLF. SERVICE AND REPAIR DAKOTA DIGITAL offers complete service and repair of itsproduct line.In addition, technicalconsultation isavailable to help you work through any questions orproblemsyou may be having installing one ofour products. Please read through the Troubleshooting Guide. There,you willfind the solution to most problems. Shouldyou everneedto send the unit back for repairs,please callour technicalsupport line,(605) 332-6513,to requesta Return MerchandiseAuthorizationnumber.Package the productin a good quality boxalong withplenty of packing material.Ship the productby UPSor insured Parcel Post.Be sure to include the RMAnumberon the package, and include a complete description ofthe problem with RMA number, yourfull name and address (streetaddresspreferred), and a telephone numberwhere you can be reached during the day.Any returns forwarrantywork must include a copyof the dated salesreceipt fromyourplace of purchase.Send no money.We will bill you after repair. Dakota DigitalLimited LifetimeWarranty DAKOTA DIGITAL warrants to the ORIGINAL PURCHASER of this productthat should it, under normal use and condition, be proven defective in material orworkmanship for the lifetime ofthe original vehicle itwas installed in, such defect(s)will be repaired orreplaced at Dakota Digital’s option. Thiswarrantydoes notcovernor extend to damage to the vehicle’ssystems, and doesnotcover removal or reinstallation of the product. ThisWarrantydoesnot applyto any product or partthereofwhich in the opinion of the Companyhasbeen damaged through alteration, improper installation, mishandling, misuse, neglect,oraccident. ThisWarranty is in lieu ofall other expressed warrantiesor liabilities. Any implied warranties, including any implied warranty of merchantability,shall be limited to the duration of thiswritten warranty. No person orrepresentative is authorized to assume, forDakota Digital,any liability other thanexpressed herein in connection with the sale ofthis product. 4510 W. 61ST St. N., Sioux Falls, SD 57107Phone:(605) 332-6513 FAX: (605) 339-4106 www.dakotadigital....