10/5/06 9:35 AM Page 1 Maintenance Before performing any maintenance, ALWAYS unplug worklight. Remove dirt and grime as soon as it accumulates. Use a soft, damp cloth and a mild soap, if needed. Be sure not to get the electrical plug wet. NEVER submerge any part of the worklight in any solution to clean it. DO NOT USE solvents such as gasoline, turpentine, etc. to clean unit. Aerosols and other chemicals may fog the clear polycarbonate lens. One Year Full Warranty on Worklight If this produc

Turning off controls will good electrical condition; and not reduce this risk. c. That wire size is large enough for AC ampere • Do not use charger outdoors. rating of charger as specified below: • Disconnect charger from power supply when not in Cord Length (Feet) 25ft. 50ft. 100ft. 150ft. use, Cord Size (AWG) 16 16 16 14 SAVE THESE INSTRUCTIONS. Review them Note: AWG = American Wire Gage frequently and use them to instruct others who may use this light. If you loan someone this light, loan the

975815. -003 Use only with Craftsman battery pack and charger (both sold separately) Extra bulb included Safety Rules and _1= CAUTION: Read Operating Instructions t: product. READ ALL INSTRUCTIONS • KNOW YOUR WORKLIGHT. Read owner's manual carefully. Learn its applications and limitations as well as the specific potential hazards related to this light. • USE ONLY BATTERY PACK PART NUMBER 975284-001 WITH YOUR WORKLIGHT. Any attempt to use another battery pack will cause damage to your light and c

9_11378 Item No. 9_11379 (1323509) (1426101 ) BATTERY PACK The battery pack for your worklight has been shipped in a low charge condition to prevent possible problems. Therefore, you should charge it overnight prior tO use. Note: Batteries will not reach full charge the first time they are charged. Allow several cycles (operating worklight followed by recharging) for batteries to become fully charged. CHARGING BATTERY PACK See Figure 1. • Charge battery pack only with the recommended charger. •

. • To reduce the risk of damage to charger body and cord, pull by charger plug rather than cord when disconnecting charger. • An extension cord should not be used unless absolutely necessary. Use of improper extension cord could result in a risk of fire and electric shock. If extension cord must be used, make sure: a. That pins on plug of extension cord are the same number, size and shape as those of plug on charger. b. That extension cord is properly wired and in good electrical condition; and

• Disconnect charger from the power supply when not in use. This will reduce theriskof electricshock or damage tothe chargerif metal items should fall into the opening.It alsowill help prevent damage to the chargerduringa power surge. • Riskof electric shock.Do not touch uninsulatedportion of outputconnector or uninsulatedbattery terminal. • Save these instructions. Refertothem frequently and usethem to instruct otherswho may usethis worklight. If you loan someonethis worklight,loanthem these in

2 • Introduction ..................................................................................................................................................................... 2 • General Safety Rules ...................................................................................................................................................... 3 • Specific Safety Rules....................................................................................................................

2 • Introduction ................................................................................................................................................................. 2 • GeneraISafety Rules ................................................................................................................................................. 3 • Specific Safety Rules .............................................................................................................................

No. de tel_fono de ayuda a los clientes: 1-800-932-3188 ° Seguridad ° Funcionamiento • Mantenimiento Sears, Roebuck and Co., 3333 Beverly Rd., Hoffman Estates, IL 60179 USA Visite la p_gina Web de Craftsman: 983000-003 2-02 _, ATENClON: Lea cuidadosamente todo este manual antes de usar su nueva luz de trabajo. Preste mucha atencibnalasReglaspara FuncionamientoSeguro,asfcomoalasAdvertenciasy Avisos. Se ha dado prioridad m_tximaa la seguridad, rendimientoy dependabilidaden el dise.=odeestaluzde tr

Deje el bloque de baterias en el cargador durante 15 a 30 minutos. Cuando el bloque de baterfas alcanza el limite de voltaje normal, el LED rojo debe iluminarse. Si el LED rojo no se ilumina despues de 30 minutos, esto indica que el bloque de baterias est_ defectuoso y debe ser reemplazado. • Despues de uso normal, se requiere un minimo de 1 hora de carga para que el bloque de baterias quede totalmente cargado. • El bloque de baterias permanecera ligeramente caliente cuando se esta cargando. Est