Votos - 3, Puntuación media: 4
(
)
)
|
Resumen del manual
Both of these consumables are available from your authorized OK International distributor as needed. The power supply features a Power Switch, green “Power On” indicator light, power cord, and a connecting port for the solder handle cord. 1. Mount the power supply in a convenient location in your workspace, such as on the workbench. 2. Insert a heater tip onto the Coil Assembly and simply push the Heater Tip all the way until it seats. You should feel a slight “ click” as it locks into place. Insert Tip onto Coil Assembly 3. With the power “Off”, attach the solder handle cord to the power supply by inserting the cord connector into the power supply connecting port. To align the 3 pins, position the flat side of the cable connector toward the 9 o'clock position of the power supply. 4. Wet the sponge with de-ionized water until it is moist but not soaked. Then place it in the workstand tray. 5. Plug the power cord into a grounded wall socket of the appropriately rated input line voltage. To turn the unit on, push the switch (located on the front of the power supply) until it latches. The green indicator light should light up. If it does not, see the “Troubleshooting Guide” in this manual. CAUTION: To provide continued protection against the risk of electric shock, connect only to properly grounded outlets. SMARTHEAT ® : NO CALIBRATION REQUIRED The PS- 900 System is comprised of an induction coil assembly and a heater tip. Each heater tip is equipped with a self-regulating heater which ‘ senses’ its own temperature and tightly maintains its pre-set idle temperature for the life of the heater- tip; all controlled by OK International’s proprietary SmartHeat ® technology. The tip temperature is determined by the inherent metallurgical properties of the heater; no external adjustment or equipment is required. The power delivered to the tip automatically varies in direct response to the thermal load. This eliminates spikes and transients associated with electrically switched elements found in conventional soldering irons. Please feel free to contact your OK International representative with any questions. (FreeText) 2 7000- 2250 Rev1 SPECIFICATIONS (FreeText) 9. WA Power Supply Ambient Operating Temperature Maximum Enclosure Temperature Input Line Voltage Input Line Frequency Power Consumption Output Power Output Frequency Power Cord (3-wire) Dimensions (approx. ) Soldering Handle and Coil Assembly Tip-to- Ground Potential Tip-to- Ground Resistance Idle Temperature Stability Handle Cord Assembly Length Connector Dimensions (approx. ) Overall length (with tip) Grip diameter Tip to grip Tip shaft diameter Tip length Workstand Dimensions 10 - 40°C Please 65°C find a 100 - 240 VAC also con 50/ 60 Hz 90 Watts max. OK I 60 Watts max. at 22°C ambient temperature defec 470 KHz owner. T 183 cm 18/3 SJT misused W = 80 mm ( 3.1" ), D = 160 mm ( 6.3" ) , warran H = 115 mm (4.5" ) replacem period w date < 2 mV True RMS, 50- 500 Hz < 2 ohms DC, unit on ± 1.1° C in still air SER 122 cm – burn proof, ESD safe 3-pin power connector OK In that fa 230 mm ( 9.06" ) with standard tips the th 13 mm (0.51" ) replacem 58 mm (2.28" ) previousl 8.0 mm (0.31" ) 82 mm (3.23" ) to 93mm ( 3.66") (typical) REPL W = 105 mm (4.1") , D = 175 mm (6.9"), OK In H = 90 mm (3.5") perio (FreeText) REPL OK Inte lifetime o replaced main wear. He abus repaired RETURN Please WARRANTY Please visit OK International's products web page (where you will find available information on systems, tips, accessories, technical notes, and more. You may also contact your local OK International representative for pricing and availability. OK International warrants the PS-900 power supply and Handle cord assembly against any defects in materials or workmanship for one ( 1) year from the date of purchase by the original owner. This Warranty excludes normal maintenance and shall not apply to any opened, misused, abused, altered or damaged items. If the product should become defective within the warranty period, OK International will repair or replace it free of charge at its sole option. The replacement item(s) will be shipped, freight prepaid, to the original purchaser. The warranty period will start from the date of purchase. If the date of purchase cannot be substantiated the date of manufacture will be used as the start of the warranty period. SERVICE AFTER WARRANTY OK International will repair or replace ( at OK International's sole option) a PS- 900 Power Supply that fails in normal use within one year (1) year after the expiration of the one- year warranty at the then current repair or exchange rate. To return a failed Power Supply for repair or replacement, follow the steps outlined below. This repair/replace offer does not apply to any previously opened, modified, repaired, altered, misused or damaged Power Supply. REPLACEABLE PS- CA3 HEATER COIL ASSEMBLY WARRANTY OK International warrants the coil assembly against mat...