Votos - 5, Puntuación media: 3.8
(
)
)
|
Resumen del manual
(refer to your manual for clearances) Mark all 14 hole centres on the wall (surface) using the template. 2. Remove the template. Depending on the surface and fasteners, drill the appropriate holes. Hold the Torch up, aligning the mounting brackets to the mounting holes. Secure the Torch to the wall using the appropriate fasteners. NOTE: The Torch has been designed to have a 1/2” clearance between the rear outer panel and the mounting surface. 3. Start the fasteners into each of the six remaining mounting holes. Align the keyholes of the frame to the heads of the fasteners and slide the frame down onto the fasteners. Ensure the frame is plumb and level before tightening the fasteners. NOTE: It is recommended that the gas and electrical be connected to the appliance at this stage. Both must enter the appliance at the opening created between the bottom of the Torch and the bottom of the mounting frame. 4. Slide the front of the cabinet over the mounting frame, ensuring the “mesh” is to the top. Start each of the four screws (supplied) through the slots. Once the cabinet has been adjusted for depth the four screws can be tightened. TMCSS MOUNTING CABINET INSTALLATION FINISHING FIGURE 6 ! WARNING Before starting the installation remove the protective layer from all three components that make up the GSST8 (cabinet, frame, and Torch) 9 W415-0689 / 06.25.08 RAIN TABS DOOR REMOVAL GLASS REMOVAL Having removed the door, lay on a smooth fl at surface, face down. There are 4 glass retainers that need to be bent away from the glass to release it from the frame. Do not pry on the glass. When replacing DO NOT SUBSTITUTE MATERIAL, replace the gasket (W562-0008) and the glass (W300-0110). Set new glass into the frame and gently bend tabs into the gasket to secure. * Ensure that the gasketed end of the glass is placed into the top of the door frame. NOTE: Care must be taken when removing and disposing of any broken glass or damaged components. Be sure to vacuum up any broken glass from inside the appliance before operation. FIGURE 9 GLASS RETAINERS GASKET* GLASS TOP FIGURE 11 BOTTOM DOOR RETAINER TOP DOOR FLANGE SECURING THE DOOR IN PLACE When shipped, the door is secured with two hitch pins along the top edge, replacing them is optional. To secure the door in place use the supplied hitch pins as illustrated. 90. 60. RAIN TAB When shipped, the rain tabs should be at a 90. angle. Push the rain tabs down until they are at an approximate 60. angle to assist rain in running off and out of the unit. HITCH PIN The door is held in place at the bottom by a retainer tab that inserts into a slot in the bottom edge of the door, and at the top with a tab that secures in the same fashion. The door is removed by lifting it off the tabs. When replacing, guide the door over the upper tab fi rst, then over the lower tab. FIGURE 8 FIGURE 10 10 W415-0689 / 06.25.08 2. Install the trim bracket supplied in your manual baggie to the fi rebox using 3 screws. DOOR CHAIN SLOT FRAME (REAR VIEW) TRIM BRACKET 1/4” (APPROX.) CONTROL DOOR 1/4” (APPROX.) With the control door closed, affi x the logo to the front face of the control door at the bottom left corner. TFSSO FRAME INSTALLATION LOGO PLACEMENT FIGURE 13 FIGURE 14 FIGURE 15 NOTE: If the frame needs to be secured, use two screws in the holes provided behind the control door. Insert the door stop chain into the receiving slot in the control door. Then insert the door chain into the receiving slot in the frame so that when fully opened the control door has a clearance of 1/8" to the mounting cabinet. NOTE: In most cases a count of 15 balls on the chain between receiving slots will be suffi cient. 1. Hang the frame onto the fi rebox by engaging the top trim bracket into the slot in the top of the frame and the bottom hooks of the frame into the slot in the mounting cabinet. FIGURE 12 TRIM BRACKET 11 W415-0689 / 06.25.08 LK8 LIGHT INSTALLATION (OPTIONAL) 1. Turn off the electrical and gas supply to the appliance. 2. Remove the frame from the unit by removing the the 2 stainless steel hex head securing screws from the bottom and lifting the frame off of the top trim bracket. 3. Lay the frame down on its front, being careful not to scratch the fi nish. 4. Starting at the top of the frame, take one light assembly and carefully snap it into place in the hole provided. Repeat for each of the light assemblies. The wires on the top 2 light assemblies will need to be fed in behind the heat shields. Note: When installing the light kit be careful not to scratch your fi ngers on any of the exposed screws in the frame. 5. Connect the light assemblies to the appropriate fl ags on the wire harness. The wire harness is labeled (TR) top right, (BR) bottom right (TL) Top left and (BL) bottom left. 6. Secure the wires into the clips at both sides and the bottom of the frame. Use the extra clips provided to retain any loose wires. 7. Re-attach frame onto unit. 8. Open the control panel door, leave the wires connected to ...
Otros modelos de este manual:Lámparas de soldar - TORCH GSST8P (1.39 mb)