Votos - 3, Puntuación media: 3.3
(
)
)
|
Resumen del manual
NOTE: Do not use a dripping wet cloth. Wring out before use. 6. MS-150/250 Models: Assemble the handle, handle guard and mounting bolt to the spatula as shown in Figure 1. 7. Re-install all removed parts. Equipment Setup GENERAL When placing the unit into service, pay attention to the following guidelines: • Make sure power to the unit is off and the unit is at room temperature. • Do not block or cover any openings on the unit. • Do not immerse cord or plug in water. • Keep cord away from heated surfaces. • Do not allow cord to hang over edge of table or counter. THIS APPLIANCE MUST BEEARTHED GROUNDEDTHIS APPLIANCE MUST BE EARTHED GROUNDED THIS APPLIANCE MUST BEEARTHED GROUNDEDTHIS APPLIANCE MUST BE EARTHED GROUNDED 120 VAC ONLY THIS APPLIANCE MUST BEEARTHED GROUNDEDTHIS APPLIANCE MUST BE EARTHED GROUNDED THIS APPLIANCE MUST BEEARTHED GROUNDEDTHIS APPLIANCE MUST BE EARTHED GROUNDED THIS UNIT IS DESIGNED TO OPERATE ON 120 VOLTS ONLY. APPLICATION WITH ANY OTHER VOLTAGE SUPPLY COMPLETELY VOIDS ALL WARRANTY. PLEASE CHECK YOUR LINE VOLTAGE BEFORE INSERTING THIS PLUG INTO THE RECEPTACLE. 208 VAC ONLY THIS APPLIANCE MUST BEEARTHED GROUNDEDTHIS APPLIANCE MUST BE EARTHED GROUNDED THIS APPLIANCE MUST BEEARTHED GROUNDEDTHIS APPLIANCE MUST BE EARTHED GROUNDED THIS UNIT IS DESIGNED TO OPERATE ON 208 VOLTS ONLY. APPLICATION WITH ANY OTHER VOLTAGE SUPPLY COMPLETELY VOIDS ALL WARRANTY. PLEASE CHECK YOUR LINE VOLTAGE BEFORE INSERTING THIS PLUG INTO THE RECEPTACLE. 220-240 VAC ONLY THIS UNIT IS DESIGNED TO OPERATE ON 220-240 VOLTS ONLY. APPLICATION WITH ANY OTHER VOLTAGE SUPPLY COMPLETELY VOIDS ALL WARRANTY. PLEASE CHECK YOUR LINE VOLTAGE BEFORE INSERTING THIS PLUG INTO THE RECEPTACLE. ELECTRICAL 1. Place the unit on a sturdy, level table or other 6 P/N 1010699 Rev. B A.J. Antunes & Co. MIRACLE STEAMER WARNING ELECTRICAL SHOCK HAZARD. FAILURE TO FOLLOW THE INSTRUCTIONS IN THIS MANUAL COULD RESULT IN SERIOUS INJURY OR DEATH. • Electrical ground is required on this appliance. • Do not modify the power supply cord plug. If it does not fit the outlet, have a proper outlet installed by a qualified electrician. • Do not use an extension cord with this appliance. • The unit should be grounded according to local electrical codes to prevent the possibility of electrical shock. It requires a grounded receptacle with separate electrical lines, protected by fuses or circuit breaker of the proper rating. • Check with a qualified electrician if you are in doubt as to whether the appliance is properly grounded. CAUTION All electrical connections must be in accordance with local electrical codes and any other applicable codes. PLUMBING NOTE: Miracle Steamer models are designed to use cold tap water. Distilled water may be used to reduce mineral deposit build-up and reduce maintenance costs. CAUTION This equipment is to be installed to comply with the basic plumbing code of the Building Officials and Code Administrators, Inc. (BOCA) and the Food Service Sanitation Manual of the Food and Drug Administration (FDA). READY Filter Sliding Cover Figure 2. Filling Water Tank–MS-150/155 READY ADDWATE R Indicator Light (Low water) Figure 3. Filling Water Tank–MS-355 Model MS-150/155 & MS-355 CAUTION Use cold water only. The MS-150/155 & MS-355 models have a self-contained water supply and is portable. To fill the self-contained water tank: 1. MS-150/155: Open the sliding tank cover on top of the unit (Figure 2). NOTE: Make sure filter inside tank is installed properly. MS-355: Open the sliding tank drawer on the side of the unit (Figure 3). 2. Pour in cold tap water. The tank will hold approximately 3 quarts (2.81 liters). 3. Close the water tank. P/N 1010699 Rev. B 7 A.J. Antunes & Co. MIRACLE STEAMER Model MS-250/255 The MS-250/255 requires a direct water hookup. An installation kit is packed inside the unit. 1. Connect the 1/4" (6.5 mm) I.D. flexible tubing to your cold water line using the supplied hose clamp. 2. Push the quick disconnect insert into the fitting on the back of the unit (Figure 4). NOTE: Incoming water is controlled by a solenoid valve inside the electrical housing of the steamer. CAUTION Water pressure must not exceed 25 psi (1.7 kg/cm2 or 172 kPa). Higher water pressures may cause poor performance or flooding. To reduce water pressure, install a water pressure regulator, and set water pressure to 20 psi (1.4 kg/cm2 or 138 kPa). To order a water pressure regulator from your authorized service center, order Roundup part no. 7000235. READY Figure 4. Connecting Water Supply to MS-250/255 Hi-Limit Reset Button Water Connect Fitting Power Cord Quick Disconnect Insert OPERATION General When the operate button (Figure 5) is pressed, power is supplied to the water pump (MS-150/155/355) or solenoid (MS-250/255). The pump/solenoid operates and water sprays onto the heated steam generator. The water flashes immediately into live steam and shoots down onto the product. One of two operational modes can be used: Single Shot or Timed Cycle SING...
Otros modelos de este manual:Vapores - MS-250/255 (880.78 kb)