Iniciar sesión:
Votos - 4, Puntuación media: 4.5 ( )

Manual de usuario Panasonic, modelo KX-TC1200ALS

Fabricar: Panasonic
Tamaño del archivo: 375.16 kb
Nombre del archivo:
Idioma del manual:en
Enlace gratuito para este manual disponible en la parte inferior de la página



Resumen del manual


Otherwise, the unit may not dial correctly. To redial the last number dialled Press (TALK) (REDIAL). To select the handset receiver volume Press (LOUD) while talking. .Each time you press the button, the volume level will change from LOW (preset) to HIGH. If noise interferes with the conversation Press (CH) to select a clearer channel or move closer to the base unit. Backlit handset keypad The handset dialling buttons will light when you press a button or lift the handset off the base unit, or when a call is received. The lights will go out a few seconds after pressing a button, lifting the handset or answering a call. (TALK) and Indicator (RINGER) If the handset is off the base unit, press (TALK). .You can also answer a call by pressing any dialling button (0) to (9), ($) or (—Any Key Talk). OR If on the base unit, just lift up. Selecting the ringer volume The TALK indicator light must be off. .To select HIGH (preset) or LOW, press (RINGER). Each time you press the button, the ringer volume will change and the selected volume will ring. .To turn the ringer OFF, press and hold (RINGER) until a beep sounds. .To turn the ringer ON, press (RINGER). For New Zealand Users Only:Additional Security Feature In the event that a call cannot be made from the handset following a power interruption, disconnect the base unit from the line momentarily then reconnect it. Turn the handset off, and replace it on the base unit. This will re-establish the security system and the handset can be used as before. Speed Dialler OSpeed D3 3 3-A Storing Phone Numbers in Memory You can store up to 10 phone numbers. The dialling buttons ((0)to (9)) function as memory stations. The TALK indicator light must be off before programming. (AUTO) TALK Indicator Memory Station Numbers (PAUSE) (PROGRAM) 1 1 Press (PROGRAM). .The TALK indicator flashes. 2 2 Enter a phone number up to 16 digits. 3 3 Press (AUTO). 4 4 Press a memory station number ((0)to (9)). .A beep sounds. .To store other numbers, repeat steps 1 through 4. .If a pause is required for dialling, press (PAUSE)where needed. Pressing (PAUSE)counts as one digit (5-C). If you misdial Press (PROGRAM)to end storing. To erase a stored number Press the memory station number ((0)to (9)) for the phone number to be erased. .A beep sounds. If you misdial Press (PROGRAM)to end storing. Start again from step 1. To erase a stored number Press (PROGRAM)(DIRECT). .A beep sounds. 1 Press (PROGRAM). .The TALK indicator flashes. 4-A Storing a Phone Number in the DIRECT Button 4 One-Touch Dialler OOne-Tou A stored number in the (DIRECT)button can be dialled with a one-touch operation. The TALK indicator light must be off before programming. TALK Indicator (PAUSE) (DIRECT) (PROGRAM) 2 Enter a phone number up to 16 digits. 3 Press (DIRECT). .A beep sounds. .If a pause is required for dialling, press (PAUSE)where needed. Pressing (PAUSE)counts as one digit (5-C). Speed Dialler Section 3/4 3-B Dialling a Stored Number (TALK)and Indicator (AUTO)...

Otros modelos de este manual:
Placas - KX-TC1200NZW (375.16 kb)
Placas - KX-TC1200NZF (375.16 kb)
Placas - KX-TC1200NZB (375.16 kb)
Placas - KX-TC1200ALW (375.16 kb)

Comentarios



Tu reseña
Tu nombre:
Introduzca dos números de la imagen:
capcha





Categoría