Votos - 5, Puntuación media: 3.8
(
)
)
|
Resumen del manual
POWER 1 CD RADIO BAND POWER2 21 3.) Tune in to a station. Manual Tuning: SKIP SEARCH Press the or buttons as many times as required until the frequency of the desired station appears on the display. TUNING Automatic Tuning: Hold the or buttons for approximately 2 seconds. The Tuner will begin scanning up or down automatically and will lock onto the next strong signal. 7 PD6900_ib_053102.p65 7 31/5/2002, 17:24 FOR BETTER RECEPTION AMFM Rotate the unit for best reception. Extend the telescopic antenna. NOTE : 1.) If you are listening to an FM Stereo station and the FM MODE switch is set to STEREO, the STEREO indicator will appear in the display. MHz FM STEREO FM MODE STEREO 2.) When too much noise is heard during FM STEREO reception, set FM MODE switch to MONO position. POWER After listening press the POWER button to power ‘Off’. PRESET RADIO STATION IN THE MEMORY The radio in this sysrtem has a 20 station memory. You can store up to 10 AM and 10 FM stations in memory. 1.) Tune to the desired station, then press 2.) Press MEMORY UP button to select the PROGRAM button. PROGRAM indicator preset memory location. Press flashes in the display. PROGRAM button, the station is stored. MONO PROGRAM MHz PROGRAM FM STEREO REPEAT PROGRAM MEMORY MEMORY UP MEMORY MHz PROGRAM FM STEREO Repeat steps 1 and 2 to store additional stations as desired. RECALLING STATIONS IN THE MEMORY 1.) Press RADIO button and BAND button 2.) Press MEMORY UP button to select the to select AM or FM. preset location, 1 to 10. CD RADIO BAND REPEAT 21 MEMORY UP 8 PD6900_ib_053102.p65 8 31/5/2002, 17:24 9 1.) Press CD button to select CD mode. 2.) Press the CD door OPEN/CLOSE area to open the door. 3.) Place a disc with the label side facing up. COMPACT DISC PLAYBACK 4.) Close the CD door by pressing on the CD door OPEN/CLOSE area. IMPORTANT! The unit should not be carried around during CD playback. If the unit is subjected to bumps and shocks during playback the disc may skip or stop. CD RADIO BAND TO INTERRUPT PLAYBACK Press the PLAY/PAUSE button once during playback. Playback stops and the track display flashes. Press the PLAY/PAUSE button again to cancel pause and resume playback at the same point in the track. The track display stops flashing. 5.) Press the PLAY/PAUSE button. Playback will begin on Track 1. PLAY/PAUSE TRACK TRACK PD6900_ib_053102.p65 9 31/5/2002, 17:24 TO STOP PLAYBACK Press the STOP button and the display shows the total tracks of the STOP disc. NOTE: After pressing the STOP button wait a few seconds for the disc to stop completely before opening the CD door. TO SKIP TO THE BEGINNING OF A TRACK • Press either one of the / SKIP SEARCH SKIP/SEARCH buttons according to the desired skip direction. REV. FWD. • Playback resumes from the selected track. TUNING • When the button is pressed once during playback, the player advances to the beginning of the next track. • When the button is pressed once during playback, the player returns to the beginning of the track being played. To go back to the beginning of the previous track press the button twice. SEARCHING FOR A PASSAGE WITHIN A TRACK • Keep the or button pressed during playback, and release the button as soon as ss you recognize the desired passage. Normal CD playback will resume from this point. REPEAT PLAYBACK This function allows a single track or all tracks on a disc to be played repeatedly. TO REPEAT THE SAME TRACK TO REPEAT THE WHOLE DISC Press the REPEAT button once during Press the REPEAT button twice until the playback. The REPEAT indicator flashes in REPEAT indicator remains in display. the display. REPEAT TRACK REPEAT TRACK REPEAT MEMORY UP TO CANCEL REPEAT PLAYBACK FUNCTION TRACK Press the REPEAT button again until REPEAT or REPEAT disappears from the display. 10 PD6900_ib_053102.p65 10 31/5/2002, 17:24 PROGRAMMED PLAYBACK Programmed playback enables tracks on a disc to be played in any desired order. Up to 21 tracks can be programmed. NOTE : Programming can only be done when the player is in Stop mode. 1.) Press the PROGRAM button. PROGRAM indicator appears in the display. PROGRAM MEMORY TRACK PROGRAM 3.) Press PROGRAM button again to memorize the track. 5.) Press the PLAY/PAUSE button to start playback. PROGRAM indicator remains in the CD display. PLAY/PAUSE TRACK PROGRAM 2.) Press the FWD or REV button to select the desired track number. PROGRAM indicator flashes in the diaplay. TRACK PROGRAM 4.) Repeat steps 2 and 3 until all desired tracks are programmed. 6.) Press STOP button to stop programmed playback. STOP 8.) To clear the programmed memory, open buttons to resume programmed the CD door or turn ‘Off’the CD player. playback. 7.) Press PROGRAM and PLAY/PAUSE RANDOM PLAYBACK Press the RANDOM button to play the tracks in random order. The RANDOM indicator appears in the display and plays all the tracks in random order. When all tracks have played, the player stops and the display shows the total tracks and playing time. Random playback can be selected while a disc...