Votos - 4, Puntuación media: 3.3
(
)
)
|
Resumen del manual
If the display is blank press the PLAY/PAUSE button to start the disc. When playback begins press the STOP button. If the disc was playing, press the STOP button so that the total tracks and playing time appear on the display. 1. While the total tracks and playing time appear on the display press the PROG (Program) button. "PROG" indicator flashes and Program No. "P - 01" appears. 2. Press SKIP FWD or SKIP REV button until the first track to be programmed appears in the display. Example: Track # 7. 3. Press the PROG (Program) button again to enter the selected track in the memory. The track indicator returns to a "00" and the Program No. advances to "P - 02". 4. Repeat Steps 2 and 3 until you have entered up to a total of 24 tracks in the memory. 5. Press the PLAY/PAUSE button to begin programmed playback. The “PROG” indicator stops flashing and remains in the display. The player will play the tracks you selected in the programmed order. When the last track has played the player stops and the total tracks and playing time appear. 6. To cancel programmed playback press the STOP button twice. The program will also be canceled if the CD Door is opened or if the power is interrupted. 10 HD2850_ib.p65 10 8/10/01, PM 03:49 ELECTRONIC ANTI-SKIP PROTECTION This CD player is equipped with an automatic 45 second Electronic Anti-Skip Memory and an Anti-Rolling Mechanism that will eliminate virtually all skipping under normal conditions. When you press the PLAY/PAUSE button to begin playback the player immediately begins to store 45 seconds of music in a solid state memory that is impervious to shock. The player is always reading the disc 45 seconds ahead of the music you are hearing and storing that information in the memory. If the player is subjected to shock or bumps of less than 45 seconds duration you will not notice them at all. If the bumps last longer than 45 seconds the anti-skip memory may be depleted and the player may skip or stop. When playback begins the Anti-Skip indicator comes on and a series of "bars" appear in the display. When all 5 "bars" appear the Anti-Skip memory contains 45 seconds of music and is "full". If the player is bumped or shaken the "bars" may start to disappear as the memory is depleted. If all 5 "bars" disappear the memory is empty and the player may skip if the bumps continue. When the bumps stop the memory starts to fill up again and all 5 "bars" will reappear. CONNECTION TO AN EXTERNAL AUDIO SYSTEM You can connect this CD player to a home stereo system, receiver, amplifier, or recorder if desired. Connect the LINE OUT jack of this CD player to the Left/Right Auxiliary Inputs, Line Inputs, or Record Inputs of the external device. The connection cable is NOT included. Set the DBBS(Bass Boost) switch of this CD player to the ‘OFF’ position. Be sure to follow the external source connection instructions for the other equipment as well. 11 HD2850_ib.p65 11 8/10/01, PM 03:49 CARE AND MAINTENANCE CLEANING THE CABINET Wipe with a soft cloth. If the cabinet is very dirty, dampen the cloth with a weak solution of neutral detergent and water, and then wipe clean. CLEANING THE LENS A dirty lens will cause sound skipping and, if the lens is very dirty, the CD may not work. Open the disc cover and clean the lens as follows: DUST OR DRY PARTICLES Using a camera lens brush/blower, blow on the lens several times, then wipe it lightly with the brush to remove dust. Then, blow on the lens once more. FINGERPRINTS To remove fingerprints from the lens, use a cotton swab starting in the middle and working to the outside edge. Use only very light pressure on the lens to avoid forcing it out of alignment. CLEANING THE DISC When a disc becomes dirty, clean it with a cleaning cloth. Wipe the disc from the center out. NOTE: Do not use solvents such as benzine, thinner; commercially available cleaners or anti-static spray intended for analog discs. 12 HD2850_ib.p65 12 8/10/01, PM 03:49 TROUBLESHOOTING GUIDE If you experience a problem with this unit, check the chart below before calling for service. SYMPTOM CAUSE SOLUTION Unit will not turn on. Weak or dead Replace batteries. batteries. CD compartment not Close CD compartment. closed. Disc will not play. Disc inserted incorrectly. Reinsert disc correctly. Dirty or defective disc. Try another disc. Moisture or condensation Disc: wipe with soft cloth. on disc or lens. Lens: see page 12 ‘Care and Maintenance’ No sound from Headphone plug not Reinsert headphone plug headphones. inserted correctly. correctly. VOLUME controls set to Raise volume controls on minimum. main unit and/or headphone cable. Weak batteries. Replace batteries. Defective disc. Try another disc. Erratic playback. Dirty or defective disc. Clean or replace disc. FOR CUSTOMER SERVICE, PLEASE WRITE TO: Emerson Radio Corp. Consumer Affairs Dept. 1901 Diplomat Drive, Farmers Branch, TX 75234. FOR ADDITIONAL SET-UP OR OPERATING ASSISTANCE PLEASE CALL: 1-800-898-9020 SERVICE 13 HD2850_ib.p65 13 8/10/...