Votos - 2, Puntuación media: 3.5
(
)
)
|
Resumen del manual
“BAL L=R” represents an equal balance between the right and left speakers. Fader Use the button to adjust the Fader between the rear and front speakers from “10R” (full rear) to “10F” ( full front). “ FAD R=F” represents an equal balance between the front and rear speakers. Loudness Control ( LOUD) When listening to music at low volume levels, this feature will boost the bass and treble ranges to compensate for the characteristics of human hearing. Press and hold the BAND/LOUD button (21) to activate this feature. “ LOUD ON” appears on the display panel. Press the BAND/ LOUD button ( 21) again to turn the LOUD function off. Audible Beep To turn on/off the audible beep heard when a function is selected, press and hold the AUDIO control button (4) on the control panel (or the S button on the remote control) to access the Beep option. Within five seconds, turn the AUDIO control (4) to choose between the following modes: “BEEP ALL”, “BEEP OFF”, or “BEEP 2ND” . Choose “BEEP 2ND” to hear a beep only when secondary functions are activated (for example, functions accessed when press and hold a button) . 5 JCD3010 Display Selector (DISP) This unit can display either the clock time or radio frequency/ CD player functions. Press the DISP button ( 6) on the control panel or remote control to display the time for approximately 5 seconds. The correct time of day can be set by pressing and holding the DISP button. Setting the Clock To set the clock, perform the following steps: 1. Press the DISP button ( 6) to display the clock. 2. Press and hold the DISP button (6) until the time display flashes. 3. Within 5 seconds, press the TUNE down button (18) to adjust the minutes to the desired setting. 4. Press the TUNE up button ( 19) to adjust the hour. 5. Press the DISP button again to return to radio frequency or disc play or wait five seconds and normal operation will resume automatically. Preset Equalizer (PEQ) The preset equalizer applies preset sound effects to the unit’s audio output signal. To adjust the preset equalizer, press the PEQ button (23) on the remote control. Press repeatedly to choose between the following modes: “FLAT” , “CLASSICS” , “POP M”, “ ROCK M” or “DSP OFF” . TUNER OPERATION 1 46 5 23 8 10 16 9 11 12 13 14 21 15 20 19 18 7 22 17 JCD3010 Select a Band Press the BAND button ( 21) on the control panel (or BND on the remote control) to change between three FM bands and one AM band. Each band stores up to six preset stations. Tuning Auto Seek Tuning Press the TUNE up (19) or TUNE down button ( 18) on the control panel (or U and D on the remote control) for less than three seconds to move to the next station automatically. Manual Tuning Press the TUNE up (19) or TUNE down button ( 18) for more than three seconds to enter manual tuning mode. Press the TUNE up or TUNE down button to change the radio frequency number up or down one step. Scan Press the SCAN button (22) on the control panel (or SCN on the remote control) to automatically search for stations. Each available station will flash on the display for a few seconds before the next is searched. To select a “flashing” station, press the SCAN button again. Preset Stations Six numbered preset buttons store and recall stations for each band. Store a Station Select a band ( if needed), then select a station. Hold a preset button (9- 14) for three seconds. The preset number will appear in the display. Recall a Station Select a band (if needed). Press a preset button (9- 14) to select the corresponding stored station. 6 JCD3010 Automatically Store / Preset Scan (AS/PS, AMS) Automatically Store Select a band (if needed) . Press the AS/PS button ( 16) on the control panel ( or the AMS button on the remote control) for more than three seconds to automatically select six strong stations and store them in the current band. The new stations replace any stations already stored in that band. Preset Scan Select a band (if needed) . Press the AS/PS button ( 16) on the control panel ( or the AMS button on the remote control) to scan stations stored in the current band. The unit will pause for ten seconds at each preset station. Press AS/PS again to stop scanning when the desired station is reached. FM Mono Select (MONO) During FM radio operation, the MONO button ( 7) is used to select monaural or stereo reception of the broadcast signal. Under normal reception conditions, the unit should be left in the stereo mode ( indicated by the “ST” icon when tuned to an FM stereo signal). If the signal is too noisy for comfortable listening, press the MONO button on the control panel (or the MO button on the remote control) . To return to stereo reception mode, press the MONO button again. CD OPERATION 1 46 5 23 8 10 16 9 11 12 13 14 21 15 20 19 18 7 22 17 JCD3010 Insert and Eject Disc Insert a disc, label-side up, with the unit turned on. “ CDP PLAY” will display on the LCD for about 5 seconds and the unit will play the first track on the disc. Press the eject button ( 2) to sto...
Otros modelos de este manual:Jugadores - JCD3010 (264.79 kb)