Votos - 2, Puntuación media: 4.5
(
)
)
|
Resumen del manual
See page 1 for further details. Peripheral Electronics®, a division of AAMP of America™ 13160 56th Court Clearwater, Florida 33760 866-788-4237 in the US or 727-572-9255 ext.262 for international calls support@peripheralelectronics.com ©2006 AAMP™ of Florida, Inc. rm11.29.06 Table of Contents Pages CHAPTER 1-Getting Started 1.1 Introduction 1 1.2 Precautions 1 1.3 Configuration & Harnesses 2 1.4 Programming the PXDP 3 CHAPTER 2-General Installation 2.1 Installation Location 4 2.2 Pre-Installation Checklist 4 2.3 Wiring Connections 4-5 2.4 Installation at Changer Location 5-6 2.4 Installation at Radio 6 CHAPTER 3 -Operation 3.1 Operation 7 3.2 Troubleshooting 8 3.3 Warranty 9 3.4 Warning 9 3.5 FCC Statement 9 Chapter 1- Getting Started 1.1 Introduction Thank you for purchasing the PXDP iPod Interface, by Peripheral Electronics®. The PXDP is designed to provide endless hours of listening pleasure through most vehicles’ factory radios. To ensure that your iPod performs correctly in your car or truck, we recommend that you read this entire manual before attempting installation of the PXDP interface. The PXDP interface will allow you to connect your iPod to a factory radio that has the ability to control a CD changer. The PXDP is designed to be used with Generation 3, 4, Mini, Photo iPods, and video capable iPods. 1.2 Precautions (Important, Please Read) UPDATING iPod FIRMWARE For proper operation of the PXDP, your iPod must be updated with the most recent version of Firmware from Apple. This is done on your computer. To Update the software on the iPod go to Follow the directions on the website to complete the download. There is no charge for this update. PREVENTING DAMAGE TO YOUR VEHICLE OR iPod. • The manufacturer recommends unplugging the iPod when not in use. To eliminate the risk of an electrical short, we recommend disconnecting the car battery in most vehicles, except in the following situations: • Vehicles equipped with on-board navigation should not have the car’s battery disconnected. Doing so may cause loss of memory settings. These settings would then have to be reprogrammed by an authorized car dealer for a fee to be paid by the vehicle’s owner. For these vehicles, we recommend extreme caution when handling exposed 12V power or ground wires/connectors. •Vehicles that incorporate a security-code protecting the radio. If the car’s battery or the radio’s power plugs are disconnected, the radio will not operate without re-entering the security-code. If you have access to the security-code, feel comfortable disconnecting the battery and the radio’s power connectors. Other wise, do not disconnect the battery and exercise extreme caution while handling exposed 12V power or ground wires/connectors. PROPER MOUNTING LOCATION Securely install the interface in a location free from; heat, humidity, moving parts or direct sunlight. Beware of hot-air flow from your vehicle’s climate control system. We recommend securing the interface to a suitable location, free of sharp metal edges, using; double sided tape, Velcro or wire ties. 1 Docking cable Vehicle specific harness PXDP interface 1.3 Configuration and Harness Selection This section will instruct you on how to properly identify and/or confirm the proper interface dip-switch configuration and vehicle specific harness selection. Please go to: Use this guide to locate your vehicle, inform you of the proper dip-switch configuration for the interface, and the vehicle specific harness that you will need for your particular vehicle. Depending on the type of PXDP kit you purchased, it might include a bundle of different vehicle harnesses or none at all. If the kit contains many harnesses, only one will be needed for your specific vehicle. If the kit came without any vehicle harness, your authorized Peripheral® dealer will have the harness for you to purchase separately. As you consult the online application guide, please take a moment to review our IMPORTANT COMPATIBILITY NOTES listed below each of the vehicle manfactuers. These notes will inform you of any issues or circumstances that can affect the compatibility of our product with your factory audio system and accessories. Some situations result in the loss of use of some factory audio players. Please read and understand these notes before proceeding to the application guide. 2 1.6 Programming the PXDP Now that you have identified the correct harness and dip-switch configuration using the application guide, it is now time to program the interface. To program the interface, set the dip-switches located on the side of the interface (see Fig.1 below) to the congfiguration listed for your vehicle in the online application guide: Switches are in their default setting of “off” in the up position and are turned “on” when switched down. Refer to the chart on the bottom of this page. This programs the PXD...