Votos - 0, Puntuación media: 4
(
)
)
|
Fotos y especificaciones Sony D-NF400 |
Resumen del manual
1 Press RADIO ON/BAND to turn on the radio. 2 Press RADIO ON/BAND to select the band. 3 Press MEMORY for 2 seconds or more. The preset number will flash in the display. 87.50 MHz FM 01 4 Press DISPLAY/MENU for 2 seconds or more. The CD player starts scanning the stations from the lower frequencies and stops for about 3 seconds when a station is received. 5 If you want to preset the received station, press DISPLAY/MENU while the preset number is flashing. The received station is preset on the preset number 1 and the CD player starts scanning for the next receivable station. If you do not press DISPLAY/MENU within the 3 seconds, the CD player will start scanning for the next receivable station without storing the station. 6 Repeat step 5 until all receivable stations are preset. If the stations have already been stored, the newly preset stations will replace the old ones. Presetting stations manually 1 Press RADIO ON/BAND to turn on the radio. 2 Press RADIO ON/BAND to select the band. 3 Press and hold MEMORY until the preset number flashes in the display. 87.50 MHz FM 01 From this step on, start the next operation within 30 seconds after you finished the previous operation. If 30 seconds pass with nothing done, the preset number stops flashing which shows that the CD player has exited the preset memory standby mode. If this happens, start from step 3 again. (Continued) Using the radio 27 Presetting radio stations 4 Press . or > repeatedly to select the preset number you want to store the station on while the preset number flashes. 5 Press TUNE + or – to tune in the station you want while the preset number flashes. 6 Press DISPLAY/MENU. When the station is preset successfully, the beep sounds. The new station replaces the old one. The preset number increases by one and the CD player enters the preset memory standby mode. 7 Repeat steps 4 to 6 when you preset the stations in the same band. When you preset the stations in the different band, press and hold MEMORY to exit the preset memory standby mode. Repeat steps 2 to 6 after the preset number stops flashing. To exit the preset memory standby mode When the radio is turned on, you can exit the preset memory standby mode using one of the following procedures. Preset stations, however, will remain stored in the CD player’s memory. • Hold down MEMORY until the preset number stops flashing. • Do not press any button for 30 seconds. The preset number stops flashing. • Press u. The CD player enters the CD playing mode. • Press x•RADIO OFF. The radio turns off. To cancel all preset stations 1 While the radio is turned off and CD play is stopped, press and hold DISPLAY/ MENU until the MENU screen appears. 2 Press V or v to select “OPTION,” then press u/ENTER. 3 Press V or v to select “TUNER PRESET,” then press u/ENTER to enter the selection. “Clear?” appears in the display. When you press u/ENTER, all the preset stations are canceled. Playing preset radio stations You can tune in the station easily by pressing . or > button. 1 Press RADIO ON/BAND to select the band. 2 Press . or > to tune in a stored station. Changing the tuning interval (Except European models) When using the CD player abroad, change the AM tuning interval on the menu, if necessary. 9 kHz area: Asia and Europe 10 kHz area: the U.S.A., Canada and South America Change it while the radio is turned off and CD play is stopped, as follows. 1 Press and hold DISPLAY/MENU until the MENU screen appears. 2 Press V or v to select “OPTION,” then press u/ENTER. 3 Press V or v to select “AM STEP,” then press u/ENTER to enter the selection. 4 Press V or v to select “9 kHz” or “10 kHz,” then press u/ENTER to enter the selection. Note After changing the tuning interval, you need to preset radio stations again. Using the radio 29 B Connecting to a power source Using the dry batteries Use only the following dry battery type for your CD player: • LR6 (size AA) alkaline batteries For the battery life, see “Specifications.” Note Be sure to remove the AC power adaptor when using the dry batteries. 1 Slide OPEN to open the lid of your CD player, then open the battery compartment lid inside the player. 2 Insert two LR6 (size AA) batteries by matching the 3 to the diagram in the battery compartment and close the lid until it clicks into place. Insert the # end first (for both batteries). When to replace the batteries You can check the remaining power of the batteries in the display. t t t t t Lo batt* * Beep sounds. When the batteries are depleted, replace both batteries with new ones. Notes • The indicator sections of roughly show the remaining battery power. One section does not always indicate one-fourth of the battery power. • Depending on operating conditions, the indicator sections of may increase or decrease. To remove the batteries Remove the batteries as illustrated below. To attach the battery compartment lid If the battery compartment lid is detached by an accidental drop, excessive force, etc., attach it as illustra...
Otros modelos de este manual:Jugadores - D-NF401 (674.99 kb)