Votos - 2, Puntuación media: 4
(
)
)
|
Resumen del manual
If you have any concerns, or experience any difficulties with your H2O Audio product, we are here to help you, so please contact us directly. We can be reached at: 1.800.708.6080 support@h2oaudio.com The most important feature of your H2O Audio Waterproof Housing is the removable T-Seal. The removable T-Seal is the main barrier between the harmful water and your iPod. It is extremely important that special attention is paid to ensure the T-Seal is seating completely in all four corners and the Housings Contact Surface. If the T-Seal is dirty, out of alignment, twisted or pinched in any way it will compromise the integrity of the housing and should not be used. H2O Audio has provided an extra T-Seal (included) in the event of annually replacement, accidental damage, loss, overexposure to direct sunlight, or if the T-Seal has become misshaped though misuse. 1. Unlatch and open case. How to install / replace the T-Seal 3. To install a new or clean T-Seal, start at any corner, push the T-Seal into the corner and run your finger along the T-Seal pushing it into the Housing Contact Surface. 4. Ensure the T-Seal is seated properly in all four corners and the Housing Contact Surface. 2. Starting at any corner, gently remove the T-seal. (Do not stretch or pull on T-Seal) Removable T-Seal Instructions This T-seal is correctly seated in a closed housing, sealing the housing and protecting the iPod from water. Correct The misaligned T-Seal becomes pinched between the base and lid (as Shown) creating an opening in the housing that will cause the housing to flood. Incorrect It is extremely important that you keep the T-Seal clean & free of sand, dirt, hair, lint, and other debris. To clean the T-Seal remove it from the housing. Wash T-Seal in warm fresh water, ensuring all debris is cleaned from the T-Seal. *Strong detergents, soaps, and chemicals MUST NEVER be used to clean the Housing or the T-Seal.* Allow T-Seal to air dry. Once dry install back into the housing. Please refer to the “How to install / replace your T-Seal” on how to properly install the T-Seal. For long term storage, store in a plastic bag out of direct sunlight. 5. Gently close lid and lock latch. The lid should close without any resistance. If you experience any resistance when closing the housing please call customer service immediately at 1.800.708.6080 x213 before using your housing. 6. Visually inspect the outside of the housing and ensure the T-seal is installed correctly. If the T-Seal is dirty, out of alignment, twisted or pinched in any way it will compromise the integrity of the housing and should not be used. How to install / replace the T-Seal Cleaning & Storing the T-Seal 7. Installing the iPod into the Housing Installing the iPod Removing the iPod 1. Align the audio port with the stereo jack in the housing. 1. Slide the player off of the stereo jack. Now the player can slide straight out of the housing. 2. Gently snap the player into the audio jack. Verify the player is completely plugged into the audio jack. NOTE: Do not disturb the T-Seal during removal of the player. If the T-Seal is moved, Please use the housing lid to completely seat the T-Seal. IMPORTANT: Remove any skins or covers from your iPod before installing it into the housing. Compatible with 2n d Gen iPod nano 6. The T-Seal DO NOT USE SILICONE GREASE as this will damage the seal. The removable, white, T-Seal (retained in the lid), between the base and the lid of the housing is what keeps your iPod safe and dry. Contact Surfaces T-Seal IT IS EXTREMELY IMPORTANT YOU ENSURE THE T-SEAL IS PROPERLY SEATED DURING EACH CLOSURE. If it is out of alignment, or twisted you will cause damage to or destroy your iPod. Prior to use, verify: 1. T-Seal is aligned properly in the Contact Surface of the lid prior to closure. 2. T-Seal and contact surface have been cleaned as necessary using a soft, lint-free cloth. 3. T-Seal and Contact Surface are free of scratches and other imperfections. Do NOT use if: 1. T-Seal is twisted, or out of alignment during closure. 2. T-Seal and Contact Surfaces have any dirt, lint, hair, and/or other debris. 3. You see scratches or imperfections on the T-Seal or Contact Surfaces. To ensure the T-Seal is fully seated in the base of the housing, firmly squeeze both sides (the base and lid) of the housing together after each insertion of the player. Always check to make sure the latch is closed and locked prior to use. If you have any questions or doubts, please contact H2O Audio Customer Support iPod nano T-Seal Water Housing 5. Unlock / Locking the Housing Unlocking your housing Locking your housing 1. Close the lid, and hook the buckle under the base. 1 3. Unhook the buckle from the base. 3 3 2. While holding the latch button towards the unlock icon, push up on the side of the latch. 2. Pull the latch towards the housing and snap in place. 2 2 1. Slide latch button towards the unlock icon. 1 3. Verify the lid and latch are closed and the button...
Otros modelos de este manual:Jugadores - iN2 (643.21 kb)