Votos - 3, Puntuación media: 3.7
(
)
)
|
Resumen del manual
The exclamation point within an equilateral triangle is intended to alert you to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. This product was tested and complies with all the requirements for the CE Mark. Compliant to 2002/95/EC (RoHS) IMPORTANT: DISPOSAL OF WASTE EQUIPMENT BY USERS IN PRIVATE HOUSEHOLDS IN THE EUROPEAN UNION This symbol on the product or on its packaging indicates that this product must not be disposed off with your other household waste. Instead, it is your responsibility to dispose of your waste equipment by handing it over to a designated collection point for the recycling of waste electrical and electronic equipment. The separate collection and recycling of your waste equipment at the time of disposal will help to conserve natural resources and ensure that it is recycled in a manner that protects human health and the environment. For more information about where you can drop off your waste equipment for recycling, please contact your local city office, your household waste disposal service or the shop where you purchased the product. Connections and operational elements Power Start 1 33 31 45 5 23 4 33 45Ambience POWER SUPPLY Power Consumption 10W 2 x 12 V AC Ground Right Left Left Right XLRCinch 6 7 8 9 10 11 1312 14 Fig. 1 (1) On/Off switch (8) Ground post (2) Start-up button with LED indicator (9) XLR output connector right channel (3) Illuminated Thorens-logo shows unit switched on (10) XLR output connector left channel (4) Speed selector 33 rpm (11) Speed fine-adjust 33 rpm (5) Speed selector 45 rpm (12) Dimmer (brightness) for display / LED (6) RCA output connector right channel (13) Speed fine-adjust 45 rpm (7) RCA output connector left channel (14) Receptacle for power supply The following pin assignment is valid for balanced XLR connectors in this unit: (1) Ground, (2) Plus, (3) Minus Mounting and set-up Carefully remove the unit and its accessories from the packaging. Supplied items: 1 x plinth (with/without tonearm) 1 x Thorens drive belt 1 x platter 1 x felt mat 1 x power supply with power cord 1 x ground lead 1 x set of RCA interconnecting leads 1 x acryl dust cover Fig. 2 1 x sprit level (bubble) 1 x tonearm balancing gauge 1 x Allen-key SW3 3 x thumb screws for adjusting 1 x adaptor for single records For the record player‘s mounting and set-up it is important to observe the following instructions. Put the plinth of the TD 550 onto a level surface as close as possible to your audio amplifier. You may verify its level position with the help of the supplied spirit level (bubble). By means of the three large thumb screws (Fig. 2) on top of the plinth the unit feet can be adjusted in height. Continue by detaching the locking screws which have been factory-installed for safe transportation. Make sure the suspended chassis is freely oscillating after having removed the screws. IMPORTANT: it is highly recommended to save the locking screws and re-install them in case the record player needs to be transported again. Now take the platter with both hands and hold its axle perpendicular over the hole in the bearing. Slowly and very carefully insert the axle into the bearing while making sure that it must not forcefully hit the bottom plate of the bearing. After the platter has been put in place turn it manually to see if it runs smoothly and with ease. Take the belt from the packaging and carefully loop it around the outer rim of platter and motor pulley. Please check if the belt sits straight on platter and pulley and is not twisted. Avoid any oil or greasy substance to get onto belt and the transmission area of platter and motor pulley. If necessary you may clean them with a lint-free tissue soaked in an alcoholic dilution (e.g. ethanol). Put felt mat on platter. It is soft and will protect your records from damages that may occur during playback. If the felt mat is to stick against the record owing to static charges, you may discharge the record before playback by running a carbon fibre brush across. For best result this brush should be connected to ground by a lead. Frequently cleaning the records with a dedicated cleaning machine can also remedy static charges. Take the three screws for adjusting the suspended chassis from the packaging and insert them into the prepared openings (Fig. 2) on top of the plinth. For sonic reason these screws cannot be firmly fixed. With the help of the supplied spirit level you can now check if the suspended chassis also is in a perfectly horizontal level. If necessary, you can re-adjust by the three screws. Please take into consideration to adapt adjustments if a particularly heavy record weight is to be employed. After having achieved a perfect level the suspended chassis should be freely oscillating and should be precisely flush with respect to the plinth‘s top plate. Connecting the record player Insert the output lead of the power supply into the receptacle (14) at...