Votos - 5, Puntuación media: 4.2
(
)
)
|
Resumen del manual
Also, make sure your floor covering will withstand 180°F. (See the Installation Safety Instructions section.) Make sure the wall coverings around your range can withstand the heat generated (up to 200°F) by the range. (See the Installation Safety Instructions section.) Moving the Range The range is very heavy. Take great care. We recommend two people maneuver the range. Ensure that the floor covering is firmly attached, or removed to prevent it being disturbed when moving the range around.You will need the leveling tool. Pull the drawer out to its furthest point. Lift up the ends of the plastic clips (one each side) to release the catches holding the drawer to the side runners and at the same time pull the drawer forward and away from the side runners. For safety’s sake push the drawer runners back out of the way. Put the drawer somewhere safe - do not refit it until you have completed the installation, you will need access to the area behind the drawer. Fit the leveling tool on the rectangular adjuster as shown below. 33 Read all instructions before installing or using this appliance. Installation Instructions Save these instructions for future reference. LOWER THE FRONT ROLLER by doing 14 complete (360°) turns clockwise. (This means turning and removing the leveling tool 56 times). Now LOWER THE TWO REAR ROLLERS. First fit the leveling tool on the hexagonal adjusting nut as shown below. Make 10 complete (360°) turns clockwise. (This means turning and removing the leveling tool 20 times). Make sure you lower BOTH REAR ROLLERS. There are two adjusting nuts, one for each roller, at both the front bottom corners of the range. Note the rollers are only intended to aid installation - the range should not be moved once it is installed. Push the range close to its final position, leaving just enough space to get behind it. Do not refit the storage drawer yet IMPORTANT! Remove all tape and packaging. Make sure the burners are properly seated and level. Take the accessory pack out of the oven. Check to be sure that no range parts have come loose during shipping. 34 Read all instructions before installing or using this appliance. Installation Instructions Save these instructions for future reference. Checking the parts Check that the range has the following parts. 4 grates Broiler pan and trivet Leveling tool Handyrack Meat tin 6 oven racks Splashback & Plinth Conversion kit from Natural gas to LP gas Rear spacer Leveling the Range Place the range in its intended position taking care not to twist it within the gap between the kitchen units as damage may occur to the range or the units. Install the oven shelves in the oven. Check for levelness by placing a spirit level or a cup, partially filled with water, on one of the oven grids. If using a spirit level, take two readings- with the level placed diagonally first in one direction and then the other. The rollers can be adjusted to level the range. To adjust the height of the rear of the range use the leveling tool supplied to turn the adjusting nuts at the front bottom corners of the range. Adjust the height of the front roller to level the range. Turn clockwise to raise the range and counter clockwise to lower. When you are satisfied with the height and level raise the front of the range by one turn of the front roller adjuster. Screw down the front feet to meet the floor. Screw the front roller adjuster counter clockwise to raise the front roller so that the front of the range is supported on the feet, not the front roller, to prevent accidental movement of the range. Leave the leveling tool in the storage drawer, so that the customer can use it if they wish to move the range. Anti-Tip Device WARNING Range must be secured by Anti-Tip bracket supplied. See instructions to install (supplied with bracket). Unless properly installed, the range could be tipped by leaning on the door. Injury might result from spilled hot liquids or from the range itself. Installing the Anti-Tip Device The Anti-Tip bracket is supplied with instructions for installation in a variety of locations. The instructions include all necessary information to complete the installation. Read the Safety Instructions and the instructions that fi t your situation before beginning installation. 35 Read all instructions before installing or using this appliance. Installation Instructions Save these instructions for future reference. Gas Connection Installation of this range must conform with local codes or, in the absence of local codes, with the National Fuel Gas Code, ANSI Z223.1-latest edition. In Canada the range must be installed in accordance with the current CGA Standard CAN/CGA-B149 -Installation Codes for Gas Burning Appliances and Equipment and/or local codes. In The Commonwealth Of Massachusetts This product must be installed by a licensed plumber or gas fitter when installed within the Commonwealth of Massachusetts. A “T” handle type manual gas valve must be installed in the gas supply line to...