Votos - 2, Puntuación media: 4
(
)
)
|
Resumen del manual
F107411-01 WARNING If the information in this manual is not followed exactly, a fire may result causing property damage, personal injury or death. WARNING The anti-tip device supplied with this range must be correctly fitted when the range is installed. This will reduce risk of tipping of the range from abnormal usage or by excessive loading of the oven door WARNING • ALL RANGES CAN TIP • INJURY TO PERSONS COULD RESULT • INSTALL ANTI-TIP BRACKET PACKED WITH RANGE • SEE INSTALLATION INSTRUCTIONS SERVICING . WARNING Disconnect from electricity before servicing. Check appliance is safe when you have finished. Sections Diagnostics 5 Servicing Procedures 11 Technical Data 27 Schematic diagram of the Range 28 3 SERVICING . WARNING Disconnect from electricity before servicing. Check appliance is safe when you have finished. 4 SERVICING . WARNING Disconnect from electricity before servicing. Check appliance is safe when you have finished. Diagnostics Checking the Multifunction Oven 6 Checking the Convection Oven 8 5 Checking the Multifunction Oven Checking the Multifunction Oven Result Possible Cause Check 1 1 2 Open the oven door and turn on the oven light Light does not work 3 4 No power to range Light bulb failed (most likely cause) Fault in power supply to switch Faulty switch Action 1 Are other parts of the range working - is the clock on, do the ovens and oven neons work? If not then there is probably no power to the range. Investigate power supply. 2 Remove the light bulb (see ‘Servicing Procedures’). Check the bulb with a resistance with a meter. The cold resistance should be very approximately 100 ohms. Replace it if it is open circuit. 3 & 4 If the bulb is OK then move the range forward (see ‘Servicing Procedures’) and remove the rear cover. With the meter check the continuity of the wiring to the bulb and the action of the switch. Replace wiring or switch as necessary. Result Check 2 Turn the function control to the Defrost setting and check that the oven fan starts to spin. Fan does not spin Remember - the clock must be set to the time of day before the oven will work. Possible Cause 1 No power to range 2 Fan blades impeded 3 Fault in power supply to switch 4 Faulty switch 5 Fault in power supply to fan 6 Fan motor faulty 1 Are other parts of the range working - is the clock on, do the oven lights and oven neons work? If not then there is probably no power to the range. Investigate power supply. 2 Remove the oven inner back and check that the fan is not impeded. 3 - 5 If the fan is not impeded, not then move the range forward (see the ‘Servicing Procedures’ section for the correct method) and remove the rear covers. With a meter check the continuity of the wiring to the fan and the action of the switch. Replace wiring, switch or fan as necessary. Action Result Possible Cause Check 3 Remove the oven racks. Turn the oven temperature Burnt out element (most likely cause) control to 400F and turn the function control to each One element Faulty switch setting in turn and check that the elements start to heat does not heat up. up. See the chart opposite. Fault in power supply to element You should be able to feel the heat from the element after few moments by holding your hand close to the element Faulty oven thermostat.(most likely cause) (DON’T TOUCH THE ELEMENTS!). No element Faulty switch The bottom element may take slightly longer to heat up. heats up Turn the controls off when you have fi nished. Fault in power supply to elements Action One element not working Remove the element - see the ‘Servicing Procedures’ section for the correct procedure. Check it with a resistance meter. Replace with a new element if necessary. If the element is OK then move the range forward (see the ‘Servicing Procedures’ section for the correct method) and check the continuity of the wiring and the thermostat. No element working Remove the range cooktop and check the thermostat and function switch 6 7 Checking the Multifunction Oven Checking the Convection Oven Result Possible Cause Check 1 1 2 Open the oven door and turn on the oven light Light does not work 3 4 No power to range Light bulb failed (most likely cause) Fault in power supply to switch Faulty switch Action 1 Are other parts of the range working - is the clock on, do the ovens and oven neons work? If not then there is probably no power to the range. Investigate power supply. 2 Remove the light bulb (see ‘Servicing Procedures’). Check the bulb with a resistance with a meter. The cold resistance should be very approximately 100 ohms. Replace it if it is open circuit. 3 & 4 If the bulb is OK then move the range forward (see ‘Servicing Procedures’) and remove the rear cover. With the meter check the continuity of the wiring to the bulb and the action of the switch. Replace wiring or switch as necessary. Check 2 Result Possible Cause Remember - the clock must be set to the time of day before the oven will work. Remove the oven racks. Turn the oven t...