Votos - 4, Puntuación media: 4
(
)
)
|
Resumen del manual
Glass Top of Firebox Spring Pin Lift the glass frame slightly, swing the top forward, then lift the glass frame to disengage it from the bottom guides. AAAA Twist 1/4 turn. Glass Frame Latch Bracket The spring pin will disengage from the latch bracket, opening the latch. Glass Frame Guide Re-Attaching the Glass Frame: a) Slide the two brackets on the bottom of the glass frame into the glass frame guides (hold the glass frame at a slight angle. b) Swing the glass frame into place - you may have to lift it slightly to allow it to fit over the top of the firebox. c) Attach the upper latches (follow the instructions above in reverse). Travis Industries 93508115 4050113 Finalizing the Installation (for qualified installers only) 23 Finalizing the Installation (for qualified installers only) 23 Glass Frame Removal and Installation (continued) The spring pin can come loose from the latch assembly. This occurs when it is turned 1/4 turn when it is disengaged. Follow the directions below to re-install the spring pin if it becomes loose. NOTE: The spring pins can be installed with the glass frame in place or removed. To re-install the spring pin, first insert this end into a 1/4” key. Insert the spring pin into this bracket with the pins aligned vertically. Push in slightly and twist 1/4 turn. With this pin horizontal, the spring pin will remain in place. Travis Industries 93508115 4050113 24 Finalizing the Installation (for qualified installers only) 24 Finalizing the Installation (for qualified installers only) Log Installation ! Make sure the gas control valve is “OFF” and the heater is cool prior to conducting service. ! Failure to position the parts in accordance with these diagrams or failure to use only parts specifically approved with this appliance may result in property damage or personal injury. NOTE: The burner must be correctly positioned. Grasp the burner, lift it up, position the gas inlet tube over the burner tube, and slide the burner all the way down (see page 35 for details). Place the rear log so the pins on the AAAAAAAAAAAAAAAAA Burner AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA Place the front right log so burner insert into the holes in the log. the pins on the burner insert into the holes in the log. Place the front left log so the pins on the burner insert into the holes in the log. The installed log set should look like this. Travis Industries 93508115 4050113 Operation 25 Operation 25 Before You Begin Warning: Read this entire manual before you use your new stove (especially the section "Safety Precautions" on pages 4 & 5). Failure to follow the instructions may result in property damage, bodily injury, or even death. Warning: Do not operate appliance with the glass front removed, cracked or broken. Replacement of the glass should be done by a licensed or qualified service person. Location of Controls - See explanation below Swing the control cover down to access the gas control valve and pilot igniter. The Pilot Flame can be found below the back log. IGNITER Pilot Igniter ON/OFF Switch The on/off switch and optional blower control are located on the back of the heater. Gas Control Valve Gas Control Knob Flame Adjust Knob An instruction card for operating the fireplace is attached to the inside of the fireplace here. Replace it for easy reference. ON OFF Optional Blower Control On/Off Switch This control is used to turn the flame on and off. Optional Blower Control This knob controls the speed of the internal convection blower that pushes heated air into the room. Gas Control Knob This knob controls gas to the stove and pilot. There are three positions: ON, OFF, and PILOT. The indicator line is to the left of the knob. Flame Adjust Knob This knob controls the flame height from low ("LO") to high ("HI”). The indicator line is above the knob. Pilot Igniter The pilot igniter is used only to start the pilot. When pressed, it sends an electrical charge to the pilot assembly. This creates a blue spark directly next to the pilot, igniting the pilot flame. ? If using a remote control or thermostat, the On/Off Switch must be left "OFF". Turning the On/Off Switch "ON" will keep the stove on always. Travis Industries 93508115 4050113 26 Operation 26 Operation Starting The Pilot Flame The pilot flame is required to ignite the main burners (it also plays a safety role). It should be left on once lit. It will stay lit unless the gas control valve is turned to "OFF". However, the pilot will go out if the gas is shut off, the propane tank runs out (or low) or if the stove malfunctions. If the pilot turns off frequently, call your dealer for information. To start the pilot follow the directions below: WARNING: When lighting or re-lighting the pilot, the glass must be removed (see page 22). a Remove the glass (see page 22 for details). b Push the gas control knob in slightly and turn it to the "OFF" position. The knob will not turn from "ON" to "OFF" unless the knob is depressed slightly. Wait five minu...