Votos - 1, Puntuación media: 3 ( )

Fabricar: Amana Tamaño del archivo: 583.26 kb Nombre del archivo: cef1d389-d0a7-46bd-b073-17a894c50f3e.pdf Idioma del manual:

MIXED FUELS •As per coal but allow additional secondary air. •The primary air inlet can be closed and burning regulated by means of the air wash above the door. ANTHRACITE Anthracite is more difficult to keep in for long periods, consequently more care in setting the controls and some familiarisation is necessary when burning anthracite. Use the smallest size fuel (Stovesse or Small Nuts). Proceed as for manufactured smokeless fuel. Leave the air inlet control open about a quarter or less. Note: The high temperature paint acquires durability by being "cured" during the initial firings of the appliance will give off fumes which are non-toxic, but which certain persons may find have an unpleasant or irritant effect. Ensure that the area is well ventilated during this time. EXTENDED BURNING The appliance will burn for an extended period provided: •Sufficient fuel is placed in the firebox. •The controls are set correctly. •Excess draught is not present in the chimney. •Fire door is closed. •If the fire goes out with unburnt fuel left in the firebox increase the air opening slightly, and vice versa. Acorn Multifuel Stoves OPERATING INSTRUCTIONS In the morning •Open the air control fully until embers begin to glow brightly and place pieces of fuel on the fire until it is well established. WARNING: When wood is burnt slowly in a closed appliance it produces moisture and tar, which will create condensation and deposits in the chimney. This effect can be minimised by burning hard for a short period, about 20 minutes, twice a day. It is usually convenient to do this morning and night. Note: To avoid chimney problems your fire should not be burnt slowly for longer than 12 hours without a period of fast burning. WARNING: Properly installed, with a suitable flue and chimney and operated and maintained this appliance will not emit fumes into the dwelling. Occasional fumes from the de-ashing and re-fuelling may occur. However, persistent fume emission is potentially dangerous and must be investigated by a Hetas registered installer. Stop using the appliance if you smell fumes or see smoke escaping. If fume emission does persist, the following immediate actions should be taken. •Open doors and windows to ventilate room. •Let the fire die or extinguish and safely dispose of fuel from the appliance. •Check for flue or chimney blockage, and clean if required. Seek expert advice from your HETAS registered installer. Do not attempt to re-light the fire until the cause of the fume emission has been identified and corrected ASH REMOVAL The appliance will require ash to be removed periodically but an ash bed of approximately 20mm (3/4'') should be maintained. Ash may be removed with a small shovel whilst the fire is still lit by raking the embers of a low fire to one side of the fire box and carefully removing the ash, then repeating the procedure for the other side. Care must be taken not to risk burning of hands or household objects from falling embers. DE - ASHING It is necessary to maintain an ash layer on the upper surface of the grate bars, in order to protect them so de-ashing should cease as soon as the first red embers drop into the ash pan. Further de-ashing will cause heat build-up under the grate, which will considerably shorten its life. This operation should be carried out with the doors closed to prevent dust escaping into the room. •Move up and down vigorously the riddling lever (ash will fall into the ash pan beneath the grate). •When de-ashing is complete re-set grate to previous position. • Empty ash pan. Note: Do not force the riddling mechanism. TO EMPTY THE ASH PAN Open the fire doors. Fit the fork end of the operating tool into the ash pan and remove from the ash pit chamber. WARNING: The ash can be very hot. Empty only to a metal container. Even if the ash appears cold, red-hot pieces of ash may be concealed and could easily start a fire or cause an injury. CLINKER The formation of clinker suggests that the unit is being over-fired. Any clinker forming on the grate should be removed when cold. OVER-FIRING Do not over fire your appliance. Using flammable liquids or too much wood or firing the stove at maximum, for prolonged periods may result in over-firing. If the chimney connector or casing glows red the appliance is being over-fired. If this occurs immediately close all air inlets to the appliance to reduce the air supply to the fire. Should a chimney fire occur immediately close the appliance down. Get everyone out of the house and call the fire brigade. A chimney fire may cause structural damage to the chimney. Do not use the appliance until the chimney and connector have been inspected and any damaged parts have been repaired or replaced. This should be done by a competent person such as a HETAS registered engineer. Acorn Multifuel Stoves OPERATING INSTRUCTIONS CLEANING Important; Under some circumstances soot can quickly build up on the throat plate and adjacent areas. The throat plate should be remov...

Descargar ahora

Introduzca dos números de la imagen: