Votos - 1, Puntuación media: 4
(
)
)
|
Resumen del manual
UL Listed=For use over electric heat source models (Wall Ovens) , UMC5200BAB/BAW/BAS • JMC5200BAW • AM C2206 BAB/BAW/BAQ/BAS To avoid risk of electrical shock, personal injury, or death, disconnect power to wall outlet before beginning installation. Parts, Tools, and Materials The following parts are supplied with the oven: Bracket Base Trim Frame Bracket Left Template 1 Bracket Bottom template 2 Bracket Top 1" Screw (1 required, 1 extra) 1/2" Screw (14 required, 6 extra) Tools required to perform installation: • Phillips Screwdriver • Saw (Electric or Hand) • Drill with 7/64" drill bits (Electric or Hand) • Tape Measure • Pencil • Framing Square ,_Level Shipping Weight • Approximate shipping weight is ?? Ibs. Cutout Dimensions Height 16 3/4" 16 3/4" Width 25 1/2" 25 1/2" Depth (min.) 23 3/4" 23 3/4" -leight Electric Heat Source Model To avoid risk of electrical shock, personal injury,or Jeath: , Before drilling into the wall, note where electrical outlets are and where electrical wire might be concealed behind the wall. YOU COULD GET AN ELECTRICAL SHOCK if you contact electrical wire with the drill bit. , Locate and disconnect the power to any electrical circuits that could be affected by installing this oven. IFYOU DO NOT DISCONNECTTHE POWER, IYOU COULD GET AN ELECTRICAL SHOCK_ Electrical rating of this oven: ,120VAC@60Hz • 13A/1100W • You need a DEDICATED 120 VAC, 60 Hz, 20A, fused electrical supply (located in the cabinet with the microwave as close as possible to the microwave) serving only the microwave. • Check with a qualified electrician if you are not sure whether the oven is properly grounded or if you do not completely understand the grounding instructions. • Do not use a fuse in the neutral or grounding circuit. )ersonal ir ,, Save these instructions for the local electrical inspectoris use. • If there is an electrical short circuit, grounding reduces the risk of electrical shock by providing an escape wire for the electric current. This appliance is equipped with a cord having a grounding wire with a grounding plug. ,, Place the plug into a properly installed and grounded outlet. • Amana does not recommend use of an extension cord. • Keep the power cord dry and do not pinch or crush it. • Do not, under any circumstances, remove the power supply cord grounding prong! • This appliance MUST be grounded! Three-prong (Grounding plug) Properly polarized grounding outlet. could be exposed to excessive microwave en- Do not expose yourself to excessive microwave energy! • DO NOT try to operate the microwave oven with the door open. • DO NOT tamper with or defeat the safety interlocks. • DO NOT place objects between the microwave oven front face and the door. • DO NOT allow soil or cleaner residue to build up on the flat surfaces around the microwave oven door. • DO NOT operate the microwave oven ifit is damaged. • The microwave oven door must close properly to operate safely. • DO NOT USE THE MICROWAVE OVEN: ,,If the door is bent. ,,If the hinges or latches are broken or loose. • If the door seals, sealing surfaces or glass is broken. • DO NOT ATTEMPT TO ADJUST OR REPAIR THE OVEN YOURSELF! • It should be adjusted and repaired by a qualified technician who can check for microwave leakage after repairing the oven. )ersonal in Before you begin installingthe oven, PLACE A PIECE OF THE CARTON OR OTHER HEAVY MATERIAL (a blanket) over the countertop or cooktop to protect it. Do not use a plastic cover. Failure to protect these 1. "SET" installment in Bracket Base 3. Fixing 'location screw' in cabinet 5. Installment of Bracket Bottom 7. Installment of Trim Frame With product, use boxed screw(4 x 20 ram). Leave the screws protruding from a minimum of 3.5 to a maximum of 4.5 mm 4,5 mmm_ Remove 4 screws from the lower right and left parts of outer panel, place "SET" in Bracket Base and fix it by tightening 4 screws again. Fix '1" screw' at the bottom of cabinet template 1. with use of Place Bracket Bottom on Bracket Base like picture B. Make holes of position A fit to Bracket Base's and fix screws after making holes with a 7/64 drill or a #35 drill. install Trim Frame to make contact 8. installment of Trim Frame cabinet. Install "Bracket Bottom" by tightening screws at screw points. 6. installment of Bracket Top 2. installment of Bracket Left 4. "SET" installment in cabinet Fix 2 screws each at the upper and lower parts of Trim Frmae with the door open. Fix it by color screw With template 2, make 2 holes each at the upper right and left parts of cabinet. (Others for the extra) Fix "Bracket Top" according to the holes. Trim Frame Dimensions (Depth of trim Frame is 7/8") Assemble the Bracket Left to outer panel. Push "SET" into the cabinet inside so that the fixed 26 _" 29 34" bottom screw of cabinet can place in the hole of Bracket Bottom. Push "SET" in until the bent part of front Bracket Base touches the front of cabinet. f 7//_ f' 27_ ,, i/_ ,, 27" Trim Frame 30" Trim Frame 34 ...