Votos - 1, Puntuación media: 3
(
)
)
|
Resumen del manual
FOR USE IN THE U.S. AND CANADA. Not SUITABLE FOR INSTALLATION IN MOBILE HOMES IF THIS HARMAN STOVE IS NOT PROPERLY INSTALLED, A HOUSE FIRE MAY RESULT. FOR YOUR SAFETY, FOLLOW INSTALLATION DIRECTIONS. CONTACT LOCAL BUILDING OR FIRE OFFICIALS ABOUT RESTRICTIONS AND INSTALLATION INSPECTION REQUIREMENTS IN YOUR AREA. Contact your local authority (such as municipal building department, fire department, fire prevention bureau, etc.) to determine the need for a permit. Cette guide d’utilisation est disponible en francais. Chez votre concessionnaire de Harman Stove Company. R1 save these instructions. Table of Contents Packing List 3 Installation 5 Mounting Blower & Filter Box 7 Wiring 8 Duct Work 11 Operation 11 Safety Tips 13 Chimney Troubleshooting 13 Maintenance 14 Specifications 15 Coil Installation 16 Oil Burner Setup 18 Warranty 19 Packing List - SF2600 Blue Angel Oil Burner Burner Gasket Automatic Draft Control Blower (2) Blower Brackets Filter Box Kit (3 pieces) + Filter Fan Control / High Limit 3-Speed Fan Switch (not on SF3500) (2) Thermostats (2) Junction Boxes Relay High Limit Snap Disc (4) 1/4 X 3/4 bolts & (4) Filter Box Mounting Clips 36” Flex Conduit (1) Straight Conduit Fitting (1) Elbow Conduit Fitting Ash Pan Shaker Handle Owner’s Manual Warranty Registration Filter Filter Box Kit Filter Box Mounting Clips Blower Snap Disc Automatic Draft Control Blower Brackets Fan Control / High Limit 3- Speed Fan Switch Thermostats Relay Oil Burner Gasket Oil Burner Ash Pan Shaker Handle Junction Boxes Flex- Conduit and Fittings Packing List for SF1500, SF2500 & SF3500 Blower Mounting Plate w/ 2= 5/16X3/4 bolts ( SF3500 Only) Automatic Draft Control Blower (2) Blower Brackets Filter Box Kit (3 pieces) + Filter Fan Control / High Limit 3-Speed Fan Switch (not on SF3500) Thermostat Junction Box Relay (4) 1/4 X 3/4 bolts & (4) Filter Box Mounting Clips 36” Flex Conduit (1) Straight Conduit Fitting (1) Elbow Conduit Fitting Ash Pan Shaker Handle Owner’s Manual Warranty Registration Filter Filter Box Kit Filter Box Mounting Clips Blower Automatic Draft Control Blower Brackets Fan Control / High Limit 3-Speed Fan Switch Thermostat Relay Blower Mount- SF3500 only Ash Pan Shaker Handle Junction Box Flex Conduit & Fittings Furnace Installation To ensure a safe installation, it is recommended that this furnace be installed by a qualified installer. The sheet metal top and sides can be easily removed to reduce the chance of dents or scratches on the painted surfaces. To remove the sheet metal, first lift off the top section. Now, the sides can be removed by lifting up and out away from the furnace. To lighten the SF2600, the oil burner heat exchanger should be removed. Do so by first removing the sheet metal as described above. Remove the front sheet metal by first removing the burner collar. Now remove the the two long bolts on each side of the heat exchanger.(Figure B) The entire unit can now be lifted off and moved separately. Caution: This furnace must not be installed closer than 24 inches at the sides and 30 inches from the rear to combustible materials. The unit may only be installed on a non-combustible floor surface such as concrete floor or concrete pad on dirt floor. The hot air plenum must be a minimum of 2 inches from the ceiling or other combustibles above the plenum. Locate the furnace as close to the chimney as possible while still maintaining the above clearances. No more than 8 feet of stovepipe should be used, including two or less 90° elbows. All horizontal runs of pipe should have a minimum 1/4 in. rise per foot. All stove pipe must be 24 gauge or thicker. When re-installing the heat exchanger, inspect the gasket around the furnace opening, and replace if necessary. (Figure A) Place the heat exchanger in position and secure with the long bolts and nuts. Be sure the gasket is compressed evenly. Re-install the sheet metal by sliding the groove on the bottom of each side panel over the steel lip on the furnace. The top sheet metal piece holds the sides in place. The SF2600 front cover gets installed by angling the bottom edge over the lip on the top of the firebox. The side edges must slide into the grooves on each side and pushed in flush with the sides and top. This front piece is held in place by the black ring which gets tightened around the burner pipe. Do not over tighten as this will push the sheet metal in too far. Inspect Gasket prior to re- installing heat exchanger. Figure A (4) 12in. bolts, two on each side, attach the heat exchanger to the furnace. Figure B Furnace Installation Installing Wood/Coal High Limit Switch- SF2600 only. First, install the sheet metal sides as described in the previous section. Install the snap disc switch into the hole on the right side sheet metal. Then mount the open backed junction box around the snap switch. Proceed with wiring as shown on page 10. Also refer to Figure D. in this section. Mounting The Oil Burner- SF2600 only. Remove oil burner unit from it’s ...
Otros modelos de este manual:Placa - SF1500A (2.6 mb)
Placa - SF2500A (2.6 mb)
Placa - SF2600A (2.6 mb)