Votos - 4, Puntuación media: 3.8
(
)
)
|
Resumen del manual
6. WARNING! The brass components of this product contain lead, a chemical known to the State of California to cause birth defects (or other reproductive harm). (California Health & Safety Code 25249.5, et seq.) 7. WARNING! The warnings, precautions, and instructions discussed in this instruction manual cannot cover all possible conditions and situations that may occur. It must be understood by the operator that common sense and 35558 35559 SKU For technical questions, please call 1-800-444-3353 PAGE 5 35560 35561 caution are factors which cannot be built into this product, but must be supplied by the operator. caution are factors which cannot be built into this product, but must be supplied by the operator. S 1. WARNING! Always make sure to close the valve on the propane tank (not included) prior to assembling the Propane Stove, performing maintenance, or making any adjustments to the unit. 2. CAUTION! This product is machine manufactured. Be aware of sharp edges. Use heavy duty work gloves and ANSI approved safety impact eye goggles when assembling. 3. Turn the Propane Stove upside down, and attach a Rubber Foot (7) to each corner of the unit. (See Assy. Diagram.) 4. For double-burner models only, the Temperature Control Knobs (4) must be attached. To do so, loosen the counter-sunk Screw in the Knob. Insert the Knob onto the Burner Control Shaft by aligning the flat edges of the Knob and Shaft. Then, firmly tighten the Screw. (See Assy. Diagram.) WARNING: The Propane Stove requires the attachment and use of the Model 91357 or Model 91359 LP Regulator & Hose Kit (UL® Listed) which are sold separately by Harbor Freight Tools. (See Figure A.) 5. To attach the Model 91357 or Model 91359 LP Regulator & Hose Kit to the Propane Stove, remove the plastic protective cap from the Inlet Connection Nozzle (5) on the Propane Stove. Next, wrap the male threads of the Inlet Connection Nozzle with about 4 inches of pipe thread seal tape (not included). Then, screw the Hose Connector firmly onto the Inlet Connection Nozzle. (See Figure A.) MODEL 91357 OR MODEL 91359 LP REGULATOR & HOSE KIT (NOT INCLUDED) TEMPERATURE INLET CONTROL KNOB (4) FIGURE A GAS VALVE PROPANE TANK (NOT INCLUDED) HOSE CONNECTOR CONNECTIONNOZZLE(5) 35558 35559 SKU For technical questions, please call 1-800-444-3353 PAGE 6 35560 35561 7. NOTE: The propane tank used must be constructed and marked in accordance with the specifications for LP propane cylinders by the U.S. Department of Transportation. (See Figure A.) 8. To connect to the propane tank, first make sure the Temperature Control Knob (4) of the Propane Stove is in its “OFF” position. Wrap the male threads of the propane tank’s discharge pipe with about 4 inches of pipe thread seal tape. Then, screw the Gas Valve of the LP Regulator & Hose Kit firmly onto the propane tank’s discharge pipe (wrench tighten). (See Figure A.) OPERATING INSTRUCTIONS 1. CAUTION! Always use clean equipment and utensils. Before using the Propane Stove, and after using this product, clean all parts in warm, clean water and anti-bacterial soap. Then, thoroughly dry. 2. NOTE: Higher altitudes may affect cooking efficiency of the Propane Stove. 3. Make sure the Propane Stove and propane tank are located on a clean, dry, level surface capable of supporting the weight of the Stove and propane tank. Keep the Propane Stove and propane tank away from other flammable objects. 4. Check to make sure the Temperature Control Knob (4) on the Propane Stove is in its “OFF” position. Open the gas valve on the propane tank and check and smell for gas leaks. Perform a bubble test by applying warm soapy water over every joint, regulator, fitting, and anywhere else there may be a possible leak. Observe carefully to see if bubbles expand, indicating a leak. A large leak can blow the soapy solution away instead of forming bubbles. If leaks are found, do not use the Propane Stove until the leaks have been stopped. After testing, make sure to close the gas valve on the propane tank. 5. For manual ignition models, open the gas valve on the propane tank. Apply a lighted match to the Burner (2) which is to be lit. Next, push the Temperature Control Knob (4) and turn it to its “ON” position. Once the Burner is lit, safely dispose of the match and adjust the Temperature Control Knob to the desired setting. (See Assy. Diagram.) 6. For Piezo Electric ignition models,a Burner (2) can be lit by pushing and turning the Temperature Control Knob (4) to its “ON” position without having to use a match. Once the Burner is lit, adjust the Temperature Control Knob to the desir...
Otros modelos de este manual:Placa - 35559 (1.51 mb)
Placa - 35560 (1.51 mb)
Placa - 35561 (1.51 mb)