Votos - 3, Puntuación media: 4.7
(
)
)
|
Resumen del manual
This is due to back-pressure in the exhaust, caused by the air flow around the house. Text Box: 5.0” Text Box: 10.812” Text Box: 11.938” Text Box: 16.625” Text Box: 1” Text Box: THROUGH WALL INSTALLATION FREESTANDING INSIDE VERTICAL INSTALLATION 1. Choose a stove location that is ideal. See the section Deciding Where to Locate Your Pellet Appliance. 2. Place a non-combustible hearth pad where necessary. 3. Place the unit on the hearth pad and space it in a manner so when the pellet vent is installed vertically, it will be 3” (76 mm) away from a combustible wall. 4. Locate the center of the fresh air intake pipe on the unit. Match that center with the same point on the wall and cut a hole about 1 5/8” (41 mm) in diameter. 5. Install the fresh air intake pipe. 6. Install the tee with clean out. 7. Install the pellet vent upward from there. When you reach the ceiling make sure that the vent goes through the ceiling firestop. Maintain a 3” (76 mm) distance to combustibles and keep attic insulation away from the pipe. 8. Finally, extend the pellet vent to go through the roof flashing. 9. Ensure that the rain cap is approximately 36” (900 mm) above the roof. FREESTANDING OUTSIDE VERTICAL INSTALLATION To accomplish the above titled installation, follow steps 1 through 8 in the previous section and then finish it by performing the following. 9. Install a tee with clean out on the outside of the house. 10. Install PL vent upward from the tee. Make sure that you install support brackets to keep the vent straight and secure. 11. Secure the flashing as you go through the roof. 12. Ensure that the rain cap is approximately 36” (900 mm) above the roof. Text Box: 1” MOBILE HOME INSTALLATION - Secure the heater to the floor using the two bolt holes supplied in the pedestal. - CAUTION: THE STUCTURAL INTEGRITY OF THE MANUFACTURED HOME FLOOR, WALL, AND CEILING/ROOF MUST BE MAINTAINED. - Ensure the unit is electrically grounded to the chassis of your home (permanently). - Do not install in a room people sleep in. - Outside fresh air is mandatory when installing into airtight homes or manufactured homes. OUTSIDE FRESH AIR CONNECTIONS A Fresh air intake is strongly recommended. Failure to install Intake air may result in improper combustion as well as the unit smoking during power failures. NOTE: Fresh air is mandatory on all units installed in “Mobile Homes” as well as in “Air Tight” homes. When connecting to an outside fresh air source, do not use plastic, combustible pipe. Only 1 5/8” diameter steel, aluminum or copper pipe should be used. It is recommended, when you are installing a fresh air system, to keep the number of bends in the pipe to a minimum. TROUBLESHOOTING DO NOT: - Hold the start-up switch down, this is a momentary contact switch and can be damaged if held down too long. - Service the stove with wet hands. The stove is an electrical appliance, which may pose a shock hazard if handled improperly. Only qualified technicians should deal with possible internal electrical failures. - Remove any screws in the firebox without first lubricating them with penetrating oil. TROUBLESHOOTING: What to do if: 1. The stove will not start 2. The stove will not operate when hot 3. The exhaust blower will not function 4. The convection blower will not function normally 5. Igniter , The pellets will not light. 6. The auger motor does not function normally 7. The Dial-A-Fire has no effect on the fire 8. The stove will not shut off 9. The stove keeps going out *NOTE: All troubleshooting procedures should be carried out by qualified technicians. 1. The stove will not start - Make sure the stove is plugged in and the wall outlet is supplying power. - Push the Start-up switch, if the stove fails to start, unplug the unit and open the hinged side panels (held tight with two screws). - With the stove unplugged, examine all connections. Make sure they are firmly connected and that there are no exposed wires touching the stove (except the chassis ground wire). - Check the continuity and placement of connections against the diagram in the back of this manual. - Ensure that the connections to the (15) minute start-up timer are correct. - Attempt to bypass the switch by inserting a jumper wire between the red and white wires that attach to the switch. Plug the stove back in. If the stove starts, replace the switch. - If this fails, replace the (15) minute start-up timer. 2. The stove will not operate when hot - Unplug the stove, open the left side panel. Jump the two brown leads that are attached to the 140°F (60°C) temperature sensor. If the stove operates replace the 140°F (60°C) sensor. 3. The exhaust motor will not function normally - Open the left side panel, check all connections against the wiring diagram. - If all the connections are verified and the exhaust blower does not function at all, tap lightly on the exhaust blower’s motor end cap, this may loosen a tight motor. - Apply 115 V directly to the exhaust blower. If the motor does ...
Otros modelos de este manual:Placa - EF-III BAY I BIH (1.2 mb)
Placa - EF-III BAY I FPI (1.2 mb)