Votos - 5, Puntuación media: 4
(
)
)
|
Resumen del manual
8 IV. FEATURES A. MINIMUM AND MAXIMUM TEMPERATURES 1. Press and release the "MIN/MAX" button. "MIN" appears in the temperature LCDs and the recorded minimum temperatures are displayed. 2. Press and release the "MIN/MAX" button to toggle to the maximum temperatures. The time of occurrence of the value for outdoor temperature will also flash. B. RESETTING THE MINIMUM AND MAXIMUM TEMPERATURES 1. To reset both the minimum and maximum temperatures—press and hold the "RESET/+" button for 4 seconds. V. MOUNTING Note: To achieve a true temperature reading, avoid mounting in direct sunlight. We recommend that you mount the remote temperature sensor on an outside North-facing wall. The sending range is 80 feet; obstacles such as walls, concrete, and large metal objects will reduce the range. Test the system by placing both units in their desired location 9 before permanently mounting. A. REMOTE TEMPERATURE SENSOR 1. Remove the mounting bracket from the remote temperature sensor. 2. Mount using either screws or adhesive tape. 3. Reattach the remote temperature sensor to the mounting bracket. B. THE TEMPERATURE STATION 1. The indoor temperature station comes with the table stand already mounted. If you wish to use the table-stand, all that is required is to place the indoor temperature station in an appropriate location. 2. To wall mount, remove the table stand. To do this, pull down on the stand from the rear and rotate forward. a) Fix a screw (not included) into the desired wall, and place the indoor temperature station onto the screw using the hanging hole on the backside. Gently pull the indoor temperature station down to lock the screw into place. TROUBLESHOOTING NOTE: For problems not solved, please contact Oreck Customer Service at 1-800-989-3535. 10 Problem: The LCD is faint Solution: Replace batteries Problem: No outdoor temperature is displayed. Solution: 1) Remove all batteries, reinsert into remote temperature sensor first, and then into the indoor temperature station. 2) Place remote temperature sensor closer to the indoor temperature station. 3) Make sure all batteries are new. 4) Place remote temperature sensor and indoor temperature station in position so the straight-line signal is not passing through more than two or three walls. Problem: Temperatures do not match if units are placed next to each other. Solution: Each temperature sensor is manufactured to be accurate, under normal conditions, to within 1 degree plus or minus and; so two temperature sensors could be as much as 2 degrees different. However, the difference can be exaggerated further because the temperature sensors are designed for different working environments. The indoor sensor is less 11 responsive to ambient air currents because of the shielding effect of the display case. In addition, the case can act as a heat sink to absorb and store heat from external sources (i.e. handling of the case or radiant heat). In addition, the much greater range of the outdoor temperature sensor requires a different calibration curve than the indoor range. Error is usually greater at the extreme ends of a range, making it harder to compare different ranges with different curves. Under non-laboratory conditions, it is difficult to compensate for the above factors and obtain an accurate comparison. MAINTENANCE AND CARE INSTRUCTIONS . Extreme temperatures, vibration, and shock should be avoided to prevent damage to the units. . Clean displays and units with a soft, damp cloth. Do not use solvents or scouring agents; they may scratch the displays and casings. . Do not submerge in water. . Do not subject the units to unnecessary heat or cold by placing them in the oven or freezer. . Opening the casings voids the warranty. Do not try to repair the unit. 12 SPECIFICATIONS Transmitting Frequency 433MHz Measuring Temperatures Indoor Temperature Station: Indoor 32°F to 156.2°F with 0.2°F resolution. (0°C to 69.0°C with 0.1°C resolution) Remote Temperature Sensor: Outdoor -21.8 °F to 156.2°F 0.2°F resolution. (-29.9°C to 69.0°C with 0.1°C resolution) Temp accuracy +/- 1°F (+/- .5°C) Transmitting range Maximum 80 feet (25m) open space Temperature check Indoor Every 10 seconds Outdoor Three times in 10 minutes Batteries—(Alkaline recommended) Remote Temperature Sensor 2 x AA, 1.5V Indoor Temperature Station 2 x AAA, 1.5V Dimensions: (L x W x H) Indoor Temperature Station 2.75 x .92 x 4.3 in. (excluding table stand) (90 x 23.6 x 110 mm) 13 Remote Temperature Sensor 1.57" x 0.9" x 5.04" (40 x 23 x 128 mm) Battery life Approximately 1 year WARRANTY INFORMATION Oreck Corporation warrants the Indoor/Outdoor Clock and Weather Station (WS-7013U) free from defects in material and workmanship under normal, non-commercial use and service. Oreck will remedy any such defects if they appear within one (1) year from date of purchase. This warranty gives you specific legal rights, and you may have other rights, which vary, from state to state. FCC ID: OMO-01RX (Receiver), OMO-01TX...
Otros modelos de este manual:Estación meteorológica - WS-7013U (124.83 kb)