Votos - 2, Puntuación media: 4 ( )

Fabricar: Worksaver Tamaño del archivo: 1.02 mb Nombre del archivo: JDBS412-633.pdf Idioma del manual:

Stop loader gradually when lowering or lifting loads. 8 SAFETY INSTRUCTIONS (continued) OPERATIONAL SAFETY (continued) Allow for additional length of loader and bale on tractor while turning. Never allow anyone to walk or work under a raised loader. Do not use loader for a work platform. Do not lift or carry anyone on loader or in bucket or on attachment. Set both front and rear tractor wheels wide for increased stability. Be sure that people, livestock, or pets are not standing near the machine while operating. ALWAYS lower loader to the ground or block securely before performing any maintenance work. Stay alert for holes, rocks and roots in the terrain and other hidden hazards. Keep away from drop-offs. Use extreme care and maintain minimum ground speed when transporting on hillside, over rough ground and when operating close to ditches or fences. Be careful when turning sharp corners. Reduce speed on slopes and sharp turns to minimize tipping or loss of control. Be careful when changing directions on slopes. Do not start or stop suddenly on slopes. Avoid operation on steep slopes. When using a unit, a minimum 20% of tractor and equipment weight must be on tractor front wheels. Without this weight, tractor could tip over, causing personal injury or death. The weight may be attained with a front end loader, front wheel weights, ballast in tires of front tractor weights. When attaining a minimum 20% of tractor and equipment weight on the front wheels, you must not exceed the ROPS weight certification. Weigh the tractor and equipment. Do not guess or estimate! Avoid excessive speed during operation. ALWAYS lower spear points to the ground when parking tractor. Raised spear points could cause injury to people or livestock. Always shut off tractor and shift to “Park” or set brakes when leaving tractor. Always lower bucket or attachment to ground. Remove key when leaving tractor unattended. Before operating equipment: if you have any questions regarding the proper assembly or operation, contact your dealer or representative. 9 SAFETY INSTRUCTIONS (continued) TRANSPORT SAFETY Comply with state and local laws governing highway safety and movement of farm machinery on public roads. The use of flashing amber lights is acceptable in most localities. However, some localities prohibit their use. Local laws should be checked for all highway lighting and marking requirements. When driving the tractor and equipment on the road or highway under 20 mph (32 kph) at night or during the day, use flashing amber warning lights and a slow moving vehicle (SMV) identification emblem. Always be sure the implement is in the proper raised position for transport. Reduce speed when transporting mounted implements to avoid bouncing and momentary loss of steering control. Plan your route to avoid heavy traffic. Make sure large round bales transported on tractor rear 3 pt. hitch do not obstruct visibility of tractor’s flashing lights or SMV sign. When transporting large round bales, keep load as low as practical to maximize tractor stability. Transporting large round bales on front loaders can limit visibility. Keep load low and go slow if visibility is obstructed. Always use extra care. Do not exceed 20 mph (32 kph). Reduce speed on rough roads and surfaces. Do not drink and drive! Watch for traffic when operating near or crossing roadways. Turn curves or go up or down hills only at a low speed and at a gradual steering angle. Make certain that at least 20% of the tractor’s weight is on the front wheels to maintain safe steerage. Slow down on rough or uneven surfaces, and loose gravel. Use extreme care and maintain minimum ground speed when transporting on hillside, over rough ground and when operating close to ditches or fences. Be careful when turning sharp corners. Never allow riders on either tractor or implement. Falling off can kill. Be a safe and courteous driver. Always yield to oncoming traffic in all situations, including narrow bridges, intersections, etc. 10 SAFETY INSTRUCTIONS (continued) MAINTENANCE SAFETY Good maintenance is your responsibility. Poor maintenance is an invitation to trouble. Follow good shop practices. - Keep service area clean and dry. - Be sure electrical outlets and tools are properly grounded. - Use adequate light for the job at hand. Make sure there is plenty of ventilation. Never operate the engine of the prime mover in a closed building. The exhaust fumes may cause asphyxiation. Before working on this machine, drive to a level area, disengage the PTO, lower implement (or if working underneath, raise and block securely), shut off the engine, set the brakes, and remove the ignition keys. Be certain all moving parts on attachments have come to a complete stop before attempting to perform maintenance. Never work under equipment unless it is blocked securely. Never depend on hydraulic system to keep implement in raised position. Keep all persons away from operator control area while performing adjustments...

Descargar ahora

Introduzca dos números de la imagen: