Votos - 2, Puntuación media: 4
(
)
)
|
Resumen del manual
Keep all persons away from operator control area while performing adjustments, service, or maintenance. Always use personal protection devices such as eye, hand and hearing protectors, when performing any service or maintenance. Periodically tighten all bolts, nuts and screws and check that all cotter pins are properly installed to ensure unit is in a safe condition. When completing a maintenance or service function, make sure all safety shields and devices are installed before placing unit in service. Openings in the skin and minor cuts are susceptible to infection from hydraulic fluid. If injured by escaping hydraulic fluid, see a doctor at once. Gangrene and death can result. Without immediate medical treatment, serious infection and reactions can occur. 11 SAFETY ( continued) MAINTENANCE SAFETY (continued) After servicing, be sure all tools, Check to ensure all safety signs are installed drawing.) Do not allow grease or oil to build up on any deck or Never replace hex bolts with less than grade five bolts unless bolt torque chart for head identification marking. Where replacement parts are necessary for periodic maintenance and servicing, parts must be used to restore your equipment to original specifications. The manufacturer will not claim responsibility for use of unapproved parts and/or accessories and other damages If equipment has been altered in any way from original design, the manufacturer does for injury or warranty. A fire extinguisher and first aid kit should be kept readily accessible while performing maintenance equipment. STORAGE SAFETY Following operation or when unhooking, stop the skid steer or tractor, set the brakes, shut off the engine, relieve all hydraulic pressure and remove the ignition keys. Store the unit in an area away from human activity. Do not park equipment where it will be exposed to livestock for long periods of time. Damage and livestock injury could result. Do not permit children to play on or around the stored unit. Make sure all parked machines are on a hard, level surface and engage all safety devices. If blocking is used, make sure it is solid and secure before leaving area. 12 SAFETY REPLACE SAFETY DECALS IF DAMAGED OR MISSING! SAFETY INFORMATION Safety is a primary concern in the design and manufacture of our products. Unfortunately, our efforts to provide safe equipment can be wiped out by a single careless act of an operator. In addition to the design and configuration of equipment, hazard control and accident prevention are dependent upon the awareness, concern, prudence and proper training of personnel involved in the operation, transport, maintenance and storage of equipment. It has been said, “The best safety device is an informed, careful operator.” We ask you to be that kind of an operator. When working on side hills, DO NOT RAISE ALWAYS OBEY ALL SAFETY RULES! LOADER TOO HIGH. Keep an eye on terrain changes. Keep load low. ALWAYS BE CAREFUL! 13 INSTRUCTIONS The Skid Steer Pallet power units or tractor loaders bucket attach system (same Skid steer units must have rated than or equal to the loads to be handled. The Skid Steer Pallet Fork can handle 4,000 pounds. Load must be equally distributed fork tines. NOTE: The 4,000 pound load rating is figured with a load center being 20 inches in front of the forklift frame. TRACTOR AND LOADER/SKID STEER REQUIREMENTS AND PREPARATION The required size of the tractor and front loader or skid steer will be determined by the weight of the load to be handled. Always use a tractor and front loader or skid steer large enough to safely handle the load. Check your tractor and front loader or skid steer to make sure they are in good working condition. Check all frame mounting bolts to make sure they are tight. Loaders that attach to the tractor frame rails should have a cross-tie installed for stability. Check the hydraulic system. Be sure the hydraulic oil and filter have been serviced according to the manufacturer’s recommendations. W ARNING! The use of any loader attachment is NOT recommended on tractors with a tricycle wheel arrangement. Tricycle type tractors are unstable for front loader use. CAUTION! It is recommended that tractors and skid steers be equipped with a roll-over protective structure (ROPS) or cab. CAUTION! Be sure your tractor or skid steer is in good condition. Read all the safety precautions and make sure all operators are familiar with the safety rules of operation. W ARNING! A heavy load can cause instability or skid steer. Make sure the rear of the tractor skid steer is properly counter-balanced Always drive slowly – especially around An unstable tractor or skid steer could steer possibly tip over, causing injury or death. The models SSPF-3742 and SSPF-3748 pallet forks can handle loads up to 4,000 lbs. Load ratings are figured with the load about 20” in front of the fork lift frame and evenly distributed between the two fork tines. NEVER put load at the ends of the fork tines – the lift capacity a...