Votos - 4, Puntuación media: 3.8
(
)
)
|
Resumen del manual
Detergent To fill the detergent compartment 1. Push the latch to open the compartment. 2. Add the required amount of detergent. The main detergent compartment (b in figure 1) has lines to allow for specific amounts of detergent. These are marked at either 15 cm3 or 25 cm3, depending on how dirty the dishes are. If your dishes are in need of an intensive wash, then add 5 cm3 of detergent into the prewash section of the compartment (a in figure 1). 3. Then close the detergent compartment lid until the latch locks. Please note: You should only use detergents designed specifically for use in dishwashers. If using dishwasher tablets, always use the detergent compartment, do not put them in the main body of the dishwasher or in the cutlery basket. The solubility of dishwasher tablets can vary depending on the temperature and duration of the programme. As a result, it is recommended that powder detergents should be used in the shorter programmes to allow better performance. CDA recommends the use of separate detergent, rinse aid and dishwasher salt rather than combination tablets as separates achieve better wash performance. If you do use combination detergents, add salt and rinse aid to the dishwasher and then adjust the water hardness setting and rinse aid setting to the minimum. When you then use separate detergents again, you should fill the salt and rinse aid compartments, adjust the water hardness setting to the maximum and run an empty wash, then adjust the water hardness setting and the rinse aid setting to the appropriate level. Salt To ensure the best efficiency, the dishwasher needs soft water. Hard water means that lime residues remain on the dishes and the interior of the dishwasher, affecting performance. The softener system is designed to remove the ions that make the water hard to provide the best quality wash performance. This is achieved by using dishwasher salt. To add dishwasher salt, follow the steps below: 1. Remove the lower dishwasher basket and then unscrew the salt compartment cap, as shown in figure 2. 2. Fill the compartment with dishwasher salt (do not use table salt), carefully to prevent unnecessary spillage. Before first use, you should fill the compartment with 2kg of dishwasher salt and then fill up the salt compartment with water (up to the brim of the compartment) as shown in figure 3. 3. Replace the cap and the lower basket. When the salt warning light on the control panel illuminates, you should refill the salt compartment with salt only – do not add water to the salt compartment after the first use. You should run a programme immediately after adding dishwasher salt, to prevent any damage to the dishwasher systems. fig. 2 fig. 1 fig. 3 Softener adjustment The efficiency of your dishwasher depends on the softness of the tap water. To ensure best efficiency, the dishwasher is equipped with a system that reduces the hardness in the mains water supply. The efficiency will increase when the system is correctly set. To find out the water hardness level of your water supply you can use the test strip supplied or alternatively contact your local water board. 1.Open the testing strip. 2. Run water through the tap for one minute. 3. Hold the testing strip in water for one second. 4. Shake the testing strip after taking it out of the water 5. Wait for one minute 6. Check the number of marks on the strip to see the level of water hardness. If the hardness of the water you use is above 60 dE or if you are using well water; you are recommended to use filter andwater refinement devices. Please note: The level of water hardness is preset to level 3. NoLimeVerylowlimecontentLowlimecontentMediumlimecontentLimecontentHighLimecontentIf the hardness of the water you use is above 63dE or if you are using well water; you are recommended to use filter and water refinement devices. Wash light is on Rinse light is on Dry light is on End light is on Wash and End lights are on Rinse and End lights are on To adjust the water softener level 1. Turn the programme selection dial to zero (reset) when the dishwasher is switched off. 2. Press and hold in the start/pause button. 3. Whilst holding in the start/pause button, switch on the dishwasher using the power on/off button. 4. Release the start/pause button once the indicator lights have flashed. The indicators will show the last selected water hardness setting. 5. To adjust to the level required, press the start/pause button until the indicators show the correct level. 6. To save the set level, press the on/off button again. Softener adjustment The efficiency of your dishwasher depends on the softness of the tap water. To ensure best efficiency, the dishwasher is equipped with a system that reduces the hardness in the mains water supply. The efficiency will increase when the system is correctly set. To find out the water hardness level of your water supply you can use the test strip supplied or alternatively contact your local water board. 1.Open the testi...
Otros modelos de este manual:Lavavajillas - WF140 (824.52 kb)
Lavavajillas - WF140 (824.52 kb)