Votos - 2, Puntuación media: 4
(
)
)
|
Resumen del manual
Should you or the individual installing this unit have any questions or comments, please contact our Customer Service Department listed below. JET-TECH SYSTEMS CORP. Tel.: +1 514-737-9701 Fax: +1 514-737-2792 e-mail: service@jet-tech.com MVP GROUP CORPORATION 5659 Royalmount Ave. Montreal, QC Canada H4P2P9 Tel: 514-737-9701 888-275-4538 Fax: 514-342-3854 / sales@mvpgroupcorp.com M\/t= ■group MANUFACTURERS LIMITED WARRANTY MVP GROUP Corporation (MVP) hereby warrants all new warewashers bearing the name “JET-TECH” and installed within the United States of America, Canada, the European Community, and the UK to be free from defects in material and workmanship, under normal and regular usage and operation, for a period of one (1) year for parts and labor. Labor shall be paid to replace any part found to be defective within this same period. NOTE: Original warranty for Model F-14 is for one (1) year for parts and ninety (90) days for labor following the date of the original installation If a defect in material(s) or workmanship is detected; or found to exist within the stated period above, MVP, at its sole discretion, shall either repair or replace any original equipment manufacturers part which has proven to fail within the machine; providing that the equipment has not been altered or tampered with in any manner, has been installed correctly as per the owners manual, and maintained and operated in complete accordance with this manual. The labor cost to repair or replace any part proven to be defective, as per above clause(s), shall be covered by MVP; provided that: the service work was performed by an authorized Jet-Tech service agency; and that this agency installed an original and genuine Jet-Tech part in the machine. Any repair work performed by a nonauthorized service depot remains the sole responsibility of the user, and MVP will not be held responsible. The installation of any generic part will not be valid; and therefore voids this warranty. All authorized labor coverage shall be limited to regular hourly rates only. Any supplemental hourly rates or charges, such as weekends or emergency premiums remain the responsibility of the user. Exceptions to above warranty are: (A) Damages resulting from shipping, handling or abuse. (B) Incorrect installation and/or connections. (C) Adjustments or calibration of any parts. (D) Faults due to lack of regular maintenance or cleaning of any internal part(s). (E) Replacement of any wearable items such as: peristaltic squeeze tubing or gaskets. (F) Excessive lime, mineral, alkali or hard water conditions (in excess 1,6-3,2 mmol/l = 160-320 PPM = 9-18 odH), and (G) Poor results due to: use of an incorrect type of detergent (for non-commercial type applications), and excessive or inadequate water temperature(s) or pressure conditions or incorrect use. MVP GROUP CORPORATION STATES THAT THERE ARE NO OTHER WARRANTIES, EXPRESSED OR IMPLIED, THAT ARE NOT SET FORTH HEREIN. MVP SHALL ASSUME NO OTHER RESPONSIBILITY, EITHER DIRECT OR NON-DIRECT, OR BE LIABLE FOR ANY OTHER OR ADDITIONAL LOSS OR DAMAGE WHETHER BEING DIRECT OR CONSEQUENTIAL, AS A RESULT OF ITS EQUIPMENT. The manufacturer reserves the rights to alter design and specifications without notice. CAP.1 INTRODUCTION...........................................................................................................2 CAP.2 DISHWASHER HANDLING AND TRANSPORT..........................................................3 2.1 Transport and packing........................................................................................................3 2.2 Handling..............................................................................................................................3 CAP.3 DANGER ZONES AND SAFETY MECHANISMS........................................................3 3.1 Danger of burns:.................................................................................................................3 3.2 Hazardous electric current:.................................................................................................3 3.3 Safety devices:....................................................................................................................3 CAP.4 INSTALLATION............................................................................................................4 4.1 Removal from packing and positioning :.............................................................................4 4.2 Electrical connections :.......................................................................................................4 4.3 Plumbing connections:........................................................................................................5 4.4 Connection to the drainage :...............................................................................................5 4.5 Limit switch connection:................................................