Votos - 1, Puntuación media: 4
(
)
)
|
Resumen del manual
Therefore please use dishwashing cycles with pre-wash when using detergent tablets. Using 3in1 detergents These products are detergents with a combined cleaning, rinsing and salt function. When the 3in1 function is activated, – the addition of special salt and rinse aid from the respective dispenser is prevented. – If the salt and rinse aid dispensers are empty, this is not indicated. – The dishwashing cycles can be up to 30 minutes longer. 3 If you want to use 3in1 detergents, check whether these detergents are suitable for your water hardness. (Follow the manufacturer’s instructions.) If you want to use 3in1 products 1.Press the ON/OFF button. 2.Press the 3IN1 button. The button indicator lights up: 3in1 function is selected. Before the start of the dishwashing cycle put 3in1 detergent in the detergent dispenser. 3 As the rinse aid inflow is automatically switched off when the 3in1 function is activated, it may come about because of the different quality standards in the 3in1 detergent, that the dishes do not dry sufficiently. If this happens, proceed as follows (see section “Adding rinse aid”): • Fill up the dispenser (if this is empty) with rinse aid. • Set rinse aid dosage to “2” mechanically. • Activate rinse aid inflow. If you do not want to use 3in1 products any more If you want to stop using 3in1 products, please do the following: • Deactivate the 3in1 function. • Fill up the dispensers for salt and rinse aid again. • Switch the water softener to the highest setting and perform up to three normal cycles without loading any dishes. • Then set the water softener to the water hardness in your area. If you want to use 4in1 products When using "4 in 1" detergents that integrate also anti- glass corrosion agent into "3 in 1" formula, please follow the same indication as given for "3 in 1" detergents. Selecting the dishwashing cycle (Cycle Table) Programme Consumption sequence values1) 1 to 2x Intermediate rinse Final rinseDrying • • 130 - 160 120 - 130 30 90 - 110 Length (minutes) 0,95 - 1,05 1,80 - 2,00 0,8 1,00 - 1,50 Energy (kWh) 14 - 16 22 - 24 9 12 - 24 Water ( litres) Dishwashing- Suitable Type of cycle for: soiling normally soiled, AUTOMATIC Dinner service Pre-wash Main wash dried-on food re • • (50° - 65°)2) and cookware mains 30 MIN Dishes, excluding just used, lightly to - • - • - (60°)3) saucepans normally soiled heavily soiled, INTENSIV Dinner service dried-on food re • • 2x • • CARE 70°4) and cookware mains, in particular protein and starch Dinner service ECO and cookware, normally soiled • • • • • 50°5) temperature-sensitive crockery 1) The consumption values were obtained under standardised conditions. They depend on how full the baskets for the dishes are. Variations are therefore possible in practice. 2) When using this cycle the degree of water clouding determines the amount of soiling on the dishes. The length of the cycle and water and energy consumption can vary greatly – depending upon the load and how dirty the dishes are. Depending upon the soiling, the temperature of the water will be automatically adjusted to between 50°C and 65°C. 3) When using this cycle, only load the dishwasher half full. 4) During the final rinse, the temperature is increased to 68° for 10 minutes to sanitize e.g. babies’ bottles, plastic chopping boards or jam jars. 5) Test programme for Test Institutes Selecting a programme When your dishes look like this, select: an intensive programme. a normal or energy-saving programme. a short programme (e.g. 30 minute programme). Starting a dishwashing cycle 1.Check that the spray arms can turn freely. 2.Turn the water tap on fully. 3.Close the door. 4.Press the ON/OFF button. 5.Select the desired cycle. The programme display lights up. The selected cycle will begin after approximately 3 seconds. Interrupting or aborting a dishwashing cycle Only interrupt a dishwashing cycle that is in progress if it is absolutely necessary. Interrupting the dishwashing programme by opening the dishwasher door 1 Hot steam may escape when the door is opened. There is a risk of scalding. 1.Open the door carefully. The dishwashing cycle will stop. 2.Close the door. The cycle will continue. Aborting the dishwashing cycle 1.Press function buttons 2 and 3 and keep them pressed. The LED indicators of all the programme buttons that can be selected light up. 2.Release the function buttons. The dishwashing cycle has been cancelled. 3.If you want to start a new cycle, check whether there is any detergent in the dispenser. 3 Turning off the dishwasher will only interrupt a selected dishwashing cycle, not cancel it. The cycle will recommence after turning the dishwasher back on again. Setting the Delay Timer Using the delay timer you can delay the start of a dishwashing cycle for 3, 6 or 9 hours. 1.Press the ON/OFF button. 2.Press the Delay Timer button repeatedly until the indicator next to the number of hours for which the start of the dishwashing cycle is to be delayed lights up, e. g. 6h, if...