Votos - 3, Puntuación media: 4.3
(
)
)
|
Resumen del manual
29 152963030en per uk.qxp 25/03/2004 15.34 Pagina 30 152963030en per uk.qxp 25/03/2004 15.34 Pagina 30 Operating instructions Maintenance and cleaning Clean the external surfaces of the machine and control panel with a damp soft cloth. If necessary use only neutral detergents. Never use abrasive products, scouring pads or solvent (acetone, trichloroethylene etc....). Ensure that the seals around the door, the detergent and rinse aid dispensers are cleaned regularly with a damp cloth. We recommend every 3 months to run a 65°C wash programme without dishes using detergent. Cleaning the filters The filters must be checked and cleaned from time to time. Dirty filters will degrade the washing result. 1. Open the door, remove the lower basket. 2. The dishwashers filter system comprises a coarse (A/B), a microfilter (C) and a flat filter (D). Some dishwashers will only have a coarse filter (A), a microfilter (C) and a flat filter (D). Unlock the filter system using the handle on the microfilter, and remove. 3. Turn the handle about 1/4 a turn anticlockwise and remove. 30 152963030en per uk.qxp 25/03/2004 15.34 Pagina 31 152963030en per uk.qxp 25/03/2004 15.34 Pagina 31 Operating instructions 4. Take hold of the coarse/fine filter (A/B) by the handle with the hole and remove from the microfilter (C). 5. Clean all filters thoroughly under running water. 6. Remove the flat filter (D) from the base of the washing compartment and clean both faces thoroughly. 7. Put the flat filter (D) back in the base of the washing compartment. 8. Place the coarse/fine filter (A/B) in the microfilter (C) and press together. 9. Put the filter combination in place and lock by turning the handle clockwise to the stop. During this process ensure that the flat filter does not protrude above the base of the washing compartment. Under no circumstances may the dishwasher be used without filters. Incorrect repositioning and fitting of the filters will produce poor washing results. NEVER try to remove the upper spray arm. If residues of soil have clogged the holes in the upper spray arm, remove them with a toothpick. 31 152963030en per uk.qxp 25/03/2004 15.34 Pagina 32 152963030en per uk.qxp 25/03/2004 15.34 Pagina 32 Operating instructions Prolonged periods of non-operation If you are not using the machine for any period of time you are advised to: 1. Unplug the appliance and then turn off the water. 2. Leave the door ajar to prevent the formation of any unpleasant smells. 3. Leave the inside of the machine clean. Frost precautions Avoid placing the machine in a location where the temperature is below 0°C. If this is unavoidable, empty the machine, close the appliance door, disconnect the water inlet pipe and empty it. Moving the machine If you have to move the machine (moving house etc....): 1. Unplug it. 2. Turn the water tap off. 3. Remove the water inlet and discharge hoses. 4. Pull the machine out together with the hoses. Avoid over tilting the machine during transportation. 32 152963030en per uk.qxp 25/03/2004 15.34 Pagina 33 152963030en per uk.qxp 25/03/2004 15.34 Pagina 33 Operating instructions What to do, when... Certain problems are due to the lack of simple maintenance or oversights, which can be solved with the help of the instructions given here, without calling out an engineer. ...a flashing fault code appears The dishwasher will not start or stops during operation. The intervention of an alarm is indicated by an intermittent audible signal and, if your appliance is equipped with an optical floor signal, in the event of an error a dot-shaped optical signal will flash on the floor: open the dishwasher door, a fault code is visible in the digital display (see following chart). Carry out the following suggested corrective actions. Fault code / Malfunction Possible cause Solutions in the digital display appears The water tap is blocked or furred with limescale. Clean the water tap. The water tap is turned off. Turn the water tap on. The machine does not fill with water The filter (where present) in the threaded hose fitting at the water inlet valve is blocked. Clean the filter in the threaded hose fitting. The water inlet hose has not been correctly laid or it is bent or squashed. Check the water inlet hose connection. in the digital display appears The sink spigot is blocked. Clean out the sink spigot. The dishwasher will not drain The water drain hose has not been correctly laid or it is bent or squashed. Check the water drain hose connection. in the digital display appears Protection against flooding is active. Close the water tap and contact your local Service Force Centre. Once the checks have been carried out, to continue the programme press the button of the programme that was running before the intervention of the alarm and close the door. The programme will continue from the point in which it was interrupted. If the fault code reappears contact your local Service Force Centre. For other combinations of fault codes not ...