Votos - 4, Puntuación media: 3.8
(
)
)
|
Resumen del manual
– Do not fill up with special salt or rinse aid. If you do not use 3in1 detergent, before using for the first time 1.Set the water softener 2.Fill up with dishwasher salt 3.Fill up with rinse aid Setting the Water Softener The water softener must be set manually and electronically: 3 To avoid scale deposits on the dishes and in the dishwasher, the dishes must be washed with soft water, i.e. water with a low lime content. The water softener must be set according to the table to the water hardness in the area where you live. Your local water company will be able to give you information about the water hardness in your area. The dishwasher must be switched off. Setting manually: 1.Open the dishwasher door. 2.Remove the lower basket from the dishwasher. 3.Turn water hardness dial on the left wall of the dishwasher interior to O or 1 (see table). Setting electronically: 1.Press the ON/OFF button. 3 If indicators for the programme buttons are lit, a dishwashing cycle is activated. The cycle must be deactivated: Press function buttons 2 and 3 simultaneously for approx. 2 seconds. All additional wash programme button indicators will go out. 2.Press function buttons 2 and 3 simultaneously and keep them pressed. The LED indicators for function buttons 1 to 3 will flash. 3.Press function button 1. The LED indicator for function button 1 will flash. The multi-display will indicate the hardness setting. 4.Pressing function button 1 increases the hardness setting by 1. (Exception: hardness setting 1 follows hardness setting 10). 5.When the hardness setting is correct, press the ON/OFF button. The hardness setting is now saved. If the water softener is set electronically to “1”, this switches off the control indicator for dishwasher salt. Adjusting the hardness Water hardness Indication on setting the multi-display in °d1) in mmol/l2) Range Manual Electronic 103) 51 -70 9,0 - 12,5 10L . 43 - 50 7,6 - 8,9 9 9L 37 - 42 6,5 - 7,5 IV 1 8 8L 29 - 36 5,1 - 6,4 7 7L 23 - 28 4,0 - 5,0 6 6L 19 - 22 3,3 - 3,9 5 5L III 15 - 18 2,6 - 3,2 4* 4L 11 -14 1,9 - 2,5 II 3 3L 0* 4 -10 0,7 - 1,8 I/II 2 2L 1 below 4 below 0.7 I no salt 1L necessary 1) (°d) German degree, measure of the hardness of water 2) [mmol/l] millimol per litre, international unit for water hardness 3) On this setting the length of the dishwashing cycle may be slightly longer. *) factory setting Adding dishwasher Salt To decalcify the water softener, it must be filled up with dishwasher salt. Use only special salt suitable for domestic dishwashers. If you do not use 3 in1 detergent, fill up with dishwasher salt: – Before using the dishwasher for the first time. – When the control indicator for dishwasher salt is illuminated on the control panel. 1.Open the door and remove the lower basket. 2.Unscrew the lid on the salt dispenser by turning it anti-clockwise. 3.Only when using the dishwasher for the first time: Fill the salt dispenser with water. 4.Place the funnel (supplied) over the dispenser opening. Fill the dispenser with dishwasher salt; the capacity of the dispenser is approx. 1.0-1.5 kg, depending on the size of the grains. Do not overfill the dispenser. 3 If water overflows when filling up with dishwasher salt, this is completely harmless. 5.Clean away any salt remnants from the dispenser opening. 6.Screw the lid back on in a clockwise direction. 7.Run a dishwashing cycle after filling the salt dispenser with dishwasher salt. This will wash away salt water and salt crystals that have been spilt. 3 Depending on the size of the salt granules, it can take several hours for the salt to dissolve in the water and for the control indicator for dishwasher salt to go out. Filling Up with Rinse Aid Rinse aid causes the rinse water to flow easily from the crockery leaving gleaming dishes and glassware. If you do not use 3in1 detergent, fill up with rinse aid: – Before using the dishwasher for the first time. – When the control indicator for rinse aid is illuminated on the control panel. Use only special rinse aid for dish washers. 1.Open the door. The rinse aid compartment is located on the inside of the dishwasher door. 2.Press the release button on the rinse aid compartment. 3.Open the cover. 4.Pour rinse aid in slowly right up to the broken “max” line; this corresponds to a volume of approx. 140 ml when full. 5.Press the lid shut until it clicks into place. 6.Wipe up any spilt rinse aid with a cloth. Otherwise there will be too much foam when rinsing. Setting the Amount of Rinse Aid Required 3 Only change the amount dispensed, if smears, milky spots (reduce the amount) or dried on water spots (increase the amount) can be seen on glasses and dishes. (See section “If dishwashing results are not satisfactory”.) The dosage can be set from 1-6. The dosage is pre-set to “4” in the factory. 1.Open the dishwasher door. 2.Press the release button on the rinse aid compartment. 3.Open the cover. 4.Set the dosage level. 5.Press the lid shut until it clicks into place. 6.If rinse aid...