Votos - , Puntuación media:
(
)
)
Fabricar: Hotpoint
Tamaño del archivo: 1.32 mb
Nombre del archivo: c952b723-b56f-471b-aad5-b3c4ab5a4aa9.pdf
Idioma del manual:
El documento se está cargando, por favor, espere
 |
El documento se está cargando, por favor, espere
Resumen del manual
•switch off at the electrical socket and unplug. • turn off the water supply tap, disconnect the inlet hose and allow to drain. •fill the rinse aid dispenser. •leave the door ajar, to prevent the build up of unpleasant odours inside the dishwasher. Before using the dishwasher after a long break, plug in and switch on at the electrical socket. Reconnect the inlet hose and turn on the water supply tap. Check there are no deposits of rust inside the water pipe, if there are allow water to run from the supply tap for a few minutes. Disconnecting the dishwasher. When disconnecting the dishwasher it is important that tasks are carried out in the correct sequence. •switch off at the mains and remove the plug from the socket. •turn off the water supply. •disconnect drain and water inlet hose. •pull out the dishwasher, carefully, withdrawing hoses at the same time. Moving the appliance. Drain water from the dishwasher. Secure all loose parts. Only transport in an upright position. •If not kept upright during transport, any water remaining inside may seep into the control module and cause subsequent errors with programme functions. D ISHWASHER Troubleshooting Caution - Do not forget that repairs should be carried out by a qualified specialist. Improper repairs can lead to considerable equipment damage, as well as danger to the user. - The dishwasher must first be disconnected from the electricity supply before any repairs or other work can be carried out. Switch off at the mains socket and water supply and remove the plug. Resolving minor problems yourself. Experience has shown that you can resolve most problems that arise during normal daily usage yourself, without having to call out a service engineer. Not only does this save costs but it also means the appliance is available for use again that much sooner. The following list of common occurences and their remedies should help you identify the causes of most problems. If the dishwasher won't start, check... Q Is the dishwasher plugged in at the electricity socket and switched on? Q Is there a power failure, check other appliances. Q Check the fuse. Q Is the water supply tap turned on? Q Is the water inlet hose connected properly? Q Is the pressure of the water supply sufficient? Q Is the inlet hose kinked? Q Is the filter on the water supply hose blocked? Q Is the dishwasher door not closed properly? If water remains inside the dishwasher, check... Q the drain hose is not kinked. Q the drain syphon is not obstructed. Q the dishwasher filters are not clogged. If the dishes are not being cleaned properly, check... Q the correct amount of detergent has been added. Q there is regenerating salt in the salt container. Q the dishes have been loaded correctly. Q the selected programme is suitable for the type of dishes and the degree of soiling. Q all filters are clean and positioned correctly. Q the spray arm nozzles are not obstructed. Q there is nothing obstructing the rotation of the spray arms. Detergent compartment lid can not be closed, check... Q has the compartment been overfilled? Q is the mechanism clogged with remnants of detergent? If the dishes fail to dry or remain dirty, check... Q there is rinse aid inside the rinse aid container. Q the rinse aid dispenser setting is correct. Q the detergent being used is of good quality and has not lost its effectiveness (for example, through incorrect storage, with the box left open). If the dishes show signs of streaking, staining etc. check... Q the rinse aid dispenser setting is not set too high. If there are visible traces of rust inside the tank, check... Q the cap off the salt container is securely closed and that the water softner setting is correct. Q the correct amount of detergent is being used. Certain detergents can be more corrosive than others. Q the tank is made of steel and therefore any rust marks are due to external elements (fragments of rust from the tank pipes, pots, cutlery etc.) Special products are commercially available to remove such marks. ...During washing Q Unusual amount of foam is created: -Has the correct detergent been used. Q Dishwasher stops suddenly during a wash cycle: -There has been a power cut. -Water supply has been interrupted. Q Knocking sound can be heard inside the dishwasher: -A spray arm is knocking against dishes. Q Rattling sound an be heard inside the dishwasher: -Crockery has not been stacked properly. Q Knocking sound can be heard coming from the inlet valves: -This is caused by the way the water pipes are laid ad it has no effect upon the way the dishwasher functions. Error messages Your dishwasher is equipped with a safety system which is able to detect operating faults. These faults flash up on the display by several codes consisting of letters and numbers. Take a note of the codes, turn the appliance off and call Hotpoint Service for technical assistance (see back page). Tap off alarm If the H2O code is flashing on the display with a long series of prolonged beeps, ...
Otros modelos de este manual:Lavavajillas - DWM75 (1.32 mb)