Votos - 2, Puntuación media: 3.5
(
)
)
|
Resumen del manual
If the message continues, call technical assistance, indicating which message appeared. If any of the other indicator lights begins to blink rapidly, turn off the appliance and call for technical assistance, indicating which light began to blink. If, despite all these checks, the dishwasher still does not function and/or the problem persists, contact the nearest authorised service centre and provide them with the following information: - the nature of the problem; - the model type number (Mod...) And the serial number (S/N...), which are indicated on the plate located on the side of the inner part of the door. Never call on unauthorised technicians and refuse to allow parts to be installed that are not original spare parts. For more detailed information about recycling of this product, please contact your local city office, your household waste disposal service or the shop where you purchased the product. Installation Positioning the Appliance Positioning the appliance in the desired rest against the wall behind it, and the cabinets or wall. The dishwasher is equipped and drain hoses that can be positioned to the facilitate proper installation. Levelling the Appliance Once the appliance is positioned, adjust the feet (screwing in or out) to adjust the dishwasher, making it level. In any the appliance should not be inclined more than 2°. If the appliance is level, it will help ensure proper performance. Cold Water Connection Connect the cold water supply hose to a threaded 3/4 (gas) connector, making sure that it is fastened tightly in place (see fig. 2). Some models are fitted with an "Aquastop" water supply hose (see fig.1) in which the small filter is already housed in the threaded end. If the water pipes are new or have not been used for an extended period of time, let the water run to make sure that the water is clear and free of impurities. If this precaution is not taken, there is a risk that the water inlet can get blocked and damage the appliance. Hot Water Connection The water supply to the appliance can also be connected to the house's hot water line (centralised system, heating system), as long as it does not exceed a temperature of 60 . . In this case,the wash cycle time will be shortened by about 15 minutes and the wash efficiency slightly reduced. The connection must be made to the hot water line following the same procedures as those for the connection to the cold water line. fig.1 fig.2 Anti-Flooding Protection The dishwasher is equipped with a system that stops the supply of water in the event of a problem with the water supply hose, or leaks within the unit, in order to prevent damage to your home. If for any reason the box containing the electrical components happens to get damaged, remove the plug for the appliance from the socket immediately. In order to guarantee that the anti-flood .9. GB GB ing feature operates properly, must be attached to the water supply tap other type of connection is acceptable. The water supply hose must not, under cut, as it contains electrical parts which are the hose is not adequate to make a proper connection, must be replaced with one which is long enough. available upon request from specialised retailers and centres. Drain Hose Connection Insert the drain hose into a drain pipe with a minimum diameter of 4cm, Or let it run into the sink, making sure to avoid bending or crimping it. Use the special plastic support that comes with the appliance (see fig.3). The free end of the hose must be at a height between 40 and 100 cm and must not be immersed in water. fig.3 Attention: The special plastic hose support must be solidly fastened to the wall to prevent the drain hose from moving and allowing water to spill outside the drain. Electrical Connection After making sure that the voltage and frequency values for the current in the home correspond to those on the rating plate (located on the stainless steel inner door of the appliance) and that the electrical system is correct for the maximum voltage on the rating plate, insert the plug into an electrical socket which is earthed properly (the earthing of the appliance is a safety requirement mandated by law). If the electrical socket to which the appliance must be connected is not appropriate for the plug, replace the plug, rather than using adaptors or the like as they could cause overheating and burns. Caution: The dishwasher plug must be accessible even when the appliance is installed as a built-in unit so that maintenance can be done safety. .10. Die Sicherheit- Aus der Nahe L A K B C D J E I F G H A Auflage von Teetasse G Filtereinsatz B Oberer Korb H Reiniger-und Klarspulbehalter C Hohenverstellung des Korbes I Salzbehalterdeckel D Oberer Spruharm J Stabchenkorb E Unter Korb K Messerhalter F Unterer Spruharm L Dritter Spruharm HINWEIS Lesen Sie bitte die Bedienungsanleitung wichtige Angaben uber die Installation, Gerates enthalt. Dieses Gerat entspricht den folgenden - 73/23/EWG vom 19. Februar 1973 (Niedri...
Otros modelos de este manual:Lavavajillas - DW12-CFE S (427.98 kb)