Votos - 0, Puntuación media: 0
(
)
)
|
Resumen del manual
To continue the count-down, press this button again. If the appliance door is opened, the count-down is not interrupted. To cancel the timer programming, press the Timer programming button 9 until none of the time indicators is illuminated. The selected programme then starts a few seconds later. Note If the power supply is disconnected while the appliance is operating, e.g. by switching off the appliance or due to a power failure, all settings remain stored. Operation continues automatically as soon as the power supply is restored. en Maintenance and care You can help prevent faults by checking and maintaining your appliance regularly. This will save time and reduce problems. Therefore you should occasionally examine the inside of your dishwasher. Overall condition of the appliance Check the rinsing compartment for grease and limescale deposits. If you find any deposits: Fill the detergent dispenser with detergent. Start the empty appliance with the programme which has the highest rinsing temperature. Clean the door seal: Wipe the door seal regularly with a damp cloth and remove any deposits. Special dishwasher salt Check the LOW SALT indicator 7 . Top up with salt, if required. Rinse-aid Check the LOW RINSE-AID indicator 10 on the front panel or the level indicator on the rinse-aid container 30 . Top up with rinse-aid, if required. Filters The filters 26 prevent larger remnants of food or other objects from getting inside the pump. This residue can occasionally clog up the filters. The filter system consists of a filter cylinder, a flat fine filter and, depending on the model, a microfilter (*). Inspect the filters for obstructions every time the dishwasher has been used. By unscrewing the filter cylinder, you can remove the filter system. Remove any food remnants and clean the filters under running water. Reassembly: Insert the filter system and screw down with the filter cylinder. en Spray arms Lime and remnants of food in the washing water can block the nozzles in the spray arms 23 and 24 and the arm mountings . Inspect the nozzles in the spray arms for blocked holes due to remnants of food. If necessary, pull the lower arm 24 upwards and lift it off. Unscrew the upper spray arm 23 . Clean both spray arms under running water. Refit the spray arms. Ensure that the lower arm has locked into place and the upper one is screwed tight. Pump * * on applicable models Larger remnants of food that have not been trapped by the filters and have been left in the water can cause a blockage in the pump. The water is no longer pumped out of the dishwasher and it can be seen covering the filter. Proceed as follows: Ladle out as much water as possible. Remove the filters 26 . Undo the screw in the cover (Torx T 20) and remove the cover. Inspect the inside and remove any obstructions that you find. Re-insert the cover and screw down. Re-insert the filters and screw down. 0 1 2 3 Spray arms Torx T20 2 1 en Fault finding Resolving minor problems yourself Experience has shown that you can resolve most problems that arise during normal daily usage yourself, without having to call out a service engineer. Not only does this save costs, but it also means that the appliance is available for use again that much sooner. The following list of common occurrences and their remedies should help you identify the causes of most problems. Problems ... ... when the appliance is switched on The appliance does not start. The mains fuse has tripped. The appliance plug has not been inserted. The appliance door has not been shut properly. The tap has not been turned on. The filter on the water supply hose is blocked. Switch off the appliance and pull out the mains plug. Turn off the tap. Then clean the filter which is situated at the connection of the supply hose. Finally, restore the power, turn on the tap and switch on the appliance. Warning Remember: The appliance may be repaired by a technician only. Improper repairs may cause considerable damage and/or injure the user. ... with the appliance itself Lower spray arm rotates with difficulty Spray arm is blocked by small items or food remains. Lid in detergent compartment cannot be closed Detergent compartment has been overfilled. Mechanism is clogged with remnants of detergent. Indicator lamps do not extinguish after washing has finished. Displays do not go out after rinsing. Programme selector 1 is not in the Off position Remnants of detergent stuck inside dispenser Compartment was damp when it was filled up with detergent. Compartment must be dry before detergent is added. There is water left in the appliance at the end of the programme. The waste water hose is blocked or kinked. The waste water pump is blocked. Filters are blocked. The programme has not ended yet. Wait until the programme ends (End-of-programme indicator 6 illuminates). Implement ”Terminate programme” function. en ... during washing Unusual amount of foam is created Normal washing up liquid has been poured into the rinse-a...
Otros modelos de este manual:Lavavajillas - SE24A250EU/36 (1.81 mb)
Lavavajillas - SE24A250EU/37 (1.81 mb)
Lavavajillas - SE25A960/35 (1.81 mb)
Lavavajillas - SE25A960/47 (1.81 mb)