Votos - 0, Puntuación media: 0
(
)
)
|
Resumen del manual
The Aqua sensor is used according to the programme. If the Aqua sensor is active, “clean” rinsing water can be transferred to the next rinse bath and water consumption can be reduced by 2–4 litres. If the turbidity is greater, the water is drained and is replaced with fresh water. In the automatic programmes the temperature and running time can also be adjusted to the degree of soiling. Switching on the appliance – Turn on the tap fully. – Switch on ON/OFF switch (. The display of the last selected programme flashes. This programme remains selected if no other programme button 0 is pressed. The expected programme duration flashes on the digital display h. – Press the START button H. The programme starts running. Remaining running time display When the programme is selected, the remaining running time of the programme is indicated on the digital display h. The running time is determined during the programme by the water temperature, the number of utensils as well as the degree of soiling and may vary (depending on the selected programme). en Timer programming * * depending on model You can delay the start of the programme in 1-hour steps up to 24 hours. – Close the door. – Switch on ON/OFF switch (. – Press button 8 + until the digital display h jumps to oe:‹‚. – Press 8 + or – button until the displayed time corresponds with your requirements. – Press START button H, timer programming is activated. – To delete timer programming, press the 8 + or – button until h oe:‹‹ is indicated on the digital display. You can change your programme selection at any time until the programme starts. End of programme The programme has ended when the value ‹:‹‹ is indicated on the numerical display h. Switching off automatically after the end of the programme * * depending on model To save energy, the dishwasher is switched off 1 minute after the programme ends (factory setting). Automatic disconnection can be adjusted from .:‹‹ to .:‹.. .:‹‹ Appliance does not switch off automatically .:‹‚ Off after 1 min .:‹. Off after 120 min – Close the door. – Switch on ON/OFF switch (. – Hold down programme button # and press START button H until •:‹... is indicated on the digital display. – Release both buttons. The LED for button # flashes and the digital display h displays the factory setting •:‹…. – Press programme button # until the factory set value .:‹‚ is indicated on the digital display h. To change the setting: – Press programme button 3. Each time the button is pressed, the set value increases by one level; when the value of .:‹. has been reached, the display jumps back to .:‹‹ (off). – Press START button H. The set value is saved. Switching off the appliance Short time after the end of the programme: – Switch off ON/OFF switch (. – Turn off the tap (not applicable if Aqua- Stop fitted). – Remove the utensils when they have cooled down. m Warning At the end of the programme please open the door fully and not partially when emptying the dishwasher. Any escaping water vapour could damage sensitive worktops. Interrupting the programme – Switch off ON/OFF switch (. The LEDs go out. The programme is saved. If the door was opened on an appliance which has a warm water connection or is heated, first leave the door ajar for several minutes and then close. Otherwise, expansion (pressure) may cause the appliance door to spring open or water to run out of the appliance. – To continue the programme, switch on the ON/OFF switch ( again. Terminating the programme (Reset) – Press START button H for approx. 3 sec. The numerical display h indicates ‹:‹‚. – The programme sequence lasts approx. 1 min. On the digital display h is indicated ‹:‹‹. – Switch off ON/OFF switch (. en Changing the programme When the START button H has been pressed, the programme cannot be changed. The only way a programme can be changed is by Cancel programme (Reset). Intensive drying The final rinse uses a higher temperature which improves the drying result. The running time may increase slightly. (Caution if utensils are delicate!) – Close the door. – Switch on ON/OFF switch (. – Hold down programme button # and press START button H until the digital display h •:‹... is indicated. – Release both buttons. The LED for button # flashes and the digital display h displays the factory setting •:‹…. – Press programme button # until the factory set value s:‹‹ is indicated on the digital display h. To change the setting, – Press the button 3 to switch the Intensive drying on s:‹‚ or off s:‹‹. – Press START button H. The set value is saved. Maintenance and care A regular inspection and maintenance of your machine will help to prevent faults. This saves time and prevents problems. Overall condition of the machine – Check spray arm for grease and limescale deposits. If you find such deposits: – Fill detergent dispenser with detergent. Start the appliance without utensils in the programme with the highest rinsing temperature. Clean the appliance with detergents/ appliance cleaner...
Otros modelos de este manual:Lavavajillas - SK75M531EU/05 (2.27 mb)
Lavavajillas - SK75M531EU/08 (2.27 mb)