Votos - 0, Puntuación media: 0
(
)
)
|
Resumen del manual
The running time is determined during the programme by the water temperature, the number of utensils as well as the degree of soiling and may vary (depending on the selected programme). en Display window Apart from information on the programme sequence, the display window )2 also indicates additional information on e.g. spray pressure. If you would no longer like to have this additional information displayed, proceed as follows. – Open the door. – Switch on ON/OFF switch (. – Hold down programme button # and press START button )" until the digital display 8 •:‹... is indicated. – Release both buttons. The LED for button # flashes and the digital display 8 displays the factory setting •:‹…. – Press programme button # until the factory set value ’:‹‚ is indicated on the digital display 8. To change the setting, – By pressing the 3 button, you can switch the on board computer (additional programme information) off ’:‹‹ or on ’:‹‚. – Press START button )". The set value is saved. – Close the door. Timer programming You can delay the start of the programme in 1 hour steps up to 24 hours. – Open the door. – Switch on ON/OFF switch (. – Press the button ` + until ‹‚ is flaching in the timer programming display X. – Press + or – button until the ` displayed time corresponds with your requirements. – Press START button )", timer programming is activated. – To delete timer programming `, press the + or – button until ‹‹ is indicated on the digital display X. You can change your programme selection at any time until the programme starts. – Close the door. End of programme The programme has ended when the value ‹:‹‹ is indicated on the numerical display 8. The end of the programme is also indicated by an acoustic signal. This function can be changed as follows: – Open the door. – Switch on ON/OFF switch (. – Hold down programme button # and press START button )" until •:‹.... is indicated on the digital display. – Release both buttons. The LED for button # flashes and the digital display 8 displays the factory setting •:‹…. – Press programme button # until the factory set value ›:‹. is indicated on the digital display 8. To change the setting, – Press programme button 3. Each time the button is pressed, the set value increases by one level; when the value of ›:‹„ has been reached, the display jumps back to ›:‹‹ (off). – Press START button )", the set value is saved. – Close the door. en Switching off automatically after the end of the programme To save energy, the dishwasher is switched off 1 minute after the programme ends (factory setting). Automatic disconnection can be adjusted from .:‹‹ to .:‹.. .:‹‹ Appliance does not switch off automatically .:‹‚ Off after 1 min .:‹. Off after 120 min – Open the door. – Switch on ON/OFF switch (. – Hold down programme button # and press START button )" until •:‹... is indicated on the digital display. – Release both buttons. The LED for button # flashes and the digital display 8 displays the factory setting •:‹…. – Press programme button # until the factory set value .:‹‚ is indicated on the digital display 8. To change the setting: – Press programme button 3. Each time the button is pressed, the set value increases by one level; when the value of .:‹. has been reached, the display jumps back to .:‹‹ (off). – Press START button )". The set value is saved. – Close the door. Switching off the appliance Short time after the end of the programme: – Open the door. – Switch off ON/OFF switch (. – Turn off the tap (not applicable if Aqua- Stop fitted). – Remove the utensils when they have cooled down. a=Warning At the end of the programme please open the door fully and not partially when emptying the dishwasher. Any escaping water vapour could damage sensitive worktops. Interrupting the programme – Open the door. – Switch off ON/OFF switch (. The LEDs go out. The programme is saved. If the door was opened on an appliance which has a warm water connection or is heated, first leave the door ajar for several minutes and then close. Otherwise, expansion (pressure) may cause the appliance door to spring open or water to run out of the appliance. – To continue the programme, switch on the ON/OFF switch ( again. – Close the door. Terminating the programme (Reset) – Open the door. – Press START button )" for approx. 3 sec. The numerical display 8 indicates ‹:‹‚. – Close the door. The programme sequence lasts approx. 1 min. On the digital display 8 is indicated ‹:‹‹. – Open the door. – Switch off ON/OFF switch (. – Close the door. Changing the programme When the START button )" has been pressed, the programme cannot be changed. The only way a programme can be changed is by Cancel programme (Reset). en Intensive drying The final rinse uses a higher temperature which improves the drying result. The running time may increase slightly. (Caution if utensils are delicate!) – Open the door. – Switch on ON/OFF switch (. – Hold down programme button # and press START button )" until •:‹.... is indicated...
Otros modelos de este manual:Lavavajillas - SMS69L12GB/18 (2.16 mb)
Lavavajillas - SMS69L12GB/22 (2.16 mb)
Lavavajillas - SMS69L12GB/23 (2.16 mb)
Lavavajillas - SMS69L12GB/25 (2.16 mb)