Votos - 0, Puntuación media: 0
(
)
)
|
Resumen del manual
The manufacturer is not liable for any consequential damage. Regularly wipe the front of the appliance and fascia with a damp cloth; water and a little washing up liquid are adequate. Do not use sponges with a rough surface or abrasive detergents, as these could scratch the surfaces. Stainless steel appliances: To prevent corrosion, avoid using sponge cloths or wash them out thoroughly several times before using for the first time. a=Warning Never use other chlorinated household detergents! Health hazard! Special salt and rinse aid – Check the refill indicators @ and H. If required, refill salt and/or rinse aid. Filters The filters 1R keep large foreign objects in the rinsing water away from the pump. These foreign objects may occasionally block the filters. The filter system consists of a coarse filter, a flat fine filter and a microfilter. – After each washing cycle check the filters for residue. – Unscrew filter cylinder as illustrated and take out filter system. –Remove any residue and clean filters under running water. –Re-install filter system in reverse sequence and ensure that the arrow marks are opposite each other after closing the filter system. en Spray arms Limescale and contaminants in the rinsing water may block nozzles and bearings on the spray arms 1: and 1B. – Check outlet nozzles on the spray arms for blockages. – Unscrew the upper spray arm 1:. – Remove the lower spray arm 1B upwards. 1 2 – Clean spray arms under running water. – Re-engage or screw on spray arms. Waste water pump Large food remnants in the rinsing water not retained by the filters may block the waste water pump. The rinsing water is then not pumped out and covers the filter. In this case: – First disconnect the appliance from the power supply. – Remove the filters 1R. – Scoop out water, use a sponge if required. – Using a spoon, prise off pump cover (as illustrated) until it clicks, then grip the cover by the lug and first pull it upwards until it resists and then pull it out forwards. 1 – Check inner compartment and remove any foreign objects. – Place cover in the original position, press down and engage. 2 3 Klick – Install filters. en Troubleshooting The majority of faults which could occur in daily operation can be rectified by the user. This ensures that the appliance is quickly available for use again. The following overview will help you locating the causes and gives helpful advise to eliminate them. a=Warning If on the digital display h an error code (“:‹‚ to “:„‹), always disconnect the appliance from the power supply and then turn off the tap. You can rectify certain faults yourself (see following fault description), for all other faults please contact customer service and state the indicated fault “:XX. a=Warning Don’t forget: Repairs may be carried out by technicians only. If a component has to be replaced, ensure that only original spare parts are used. Improper repairs or use of non-original spare parts may cause considerable damage and put the user at considerable risk. ... when the appliance is switched on The appliance does not start. – The mains fuse has tripped. – The appliance plug has not been inserted. – The appliance door has not been shut properly. ... changing settings A setting cannot be changed, a programme starts. – Wrong programme button pressed. Terminate the programme (see chapter entitled “Terminating the programme (Reset)”) and start all over again. – You did not wait until programme ended. ... on the appliance Lower spray arm rotates sluggishly. – Spray arm blocked. The door is difficult to open. * – Child-proof lock is activated. The deactivation instructions are at the back in the envelope. * depending on model Door cannot be closed. – Door lock has been activated. To reset, close the door with greater force. Cover on the detergent dispenser cannot be closed. – Detergent dispenser overfilled or mechanism blocked by sticky detergent residue. Detergent residue in the detergent dispenser. – Dispenser was damp when filled. “Check water supply” display 8 lights up. – Tap turned off. – Water supply interrupted. – Supply hose kinked. – Filter in the water supply blocked. – Switch off the appliance and pull out the mains plug. – Turn off the tap. – Clean filter in the supply hose. –Reconnect power supply. –Turn on the tap. –Switch on the appliance. en – Water is left in the appliance at the end of the programme. – (“:.…) Waste water hose is blocked or kinked. Filters blocked. – (“:.†) Waste water pump blocked, cover on the waste water pump is not locked in position (see Maintenance and care). – Filters blocked. – The programme has not yet ended. Wait until programme ends (digital display indicates ‹:‹‹) or implement the “Reset” function. Refill indicator for salt @ and/or rinse- aid H is not lit. – Refill indicator/s switched off. – Adequate salt/rinse-aid available. Refill indicator for special salt @ is lit. – No salt. Refill with special salt. – Sensor does not detect salt tablets. Use diff...
Otros modelos de este manual:Lavavajillas - SMV53M20EU/13 (1.83 mb)
Lavavajillas - SMV65M10EU/01 (1.83 mb)
Lavavajillas - SMV65M10EU/02 (1.83 mb)
Lavavajillas - SMV65M10EU/13 (1.83 mb)