Votos - 0, Puntuación media: 0
(
)
)
|
Resumen del manual
– Hold down the button + for approx. 4 sec. until this ’– is indicated on the digital display. If any button is pressed while the programme is running, this ’– is indicated on the digital display. It is not possible to end (Reset) the programme. Deactivating the button lock: – Hold down the button + for approx. 4 sec. until the display ’– goes out. When the programme ends (‹:‹‹ on the digital display), the button lock is cancelled. If there is a power failure, the button lock is retained. Whenever a programme is restarted, the button lock must be reactivated. Damage – The appliance may be repaired and opened up by a technician only. To do this, disconnect the appliance from the power supply. Pull out the mains plug or switch off the fuse. Turn off the tap. Disposal – Make redundant appliances unusable to prevent subsequent accidents. – Dispose of the appliance in an environmentally friendly manner. a=Warning Children could become locked in the appliance (risk of suffocation) or find themselves in other dangerous situations. Therefore: Pull out the mains plug, sever and dispose of the power cord. Destroy the door lock so that the door can no longer be closed. en Getting to know your appliance Diagrams of the control panel and the interior of the appliance can be found in the envelope at the front. Individual positions are referred to in the text. Control panel ( ON/OFF switch 0 Programme buttons ** 8 Door opener @ Timer programming * H Additional options ** P START button X Display “Check water supply” ` Salt refill indicator h Rinse aid refill indicator )" Digital display * depending on model ** Number depending on model Appliance interior 1" Top basket 1* Knife shelf * 12 Tablet collecting tray 1: Upper spray arms 1B Bottom spray arm 1J Dispenser for special salt 1R Filters 1Z Cutlery basket 1b Bottom basket 1j Dispenser for rinse aid 9" Detergent dispenser 9* Lock for detergent dispenser 92 Rating plate * depending on model Overview of menu The settings can be found in the individual chapters. • Water Hardness •:‹‹ -•:‹. s Intensive drying s:‹‹ -s:‹‚ § Rinse aid §:‹‹ -§:‹‡ ‘ Hot water ‘:‹‹ -‘:‹‚ . Automatic disconnection .:‹‹ -.:‹. en Water hardness table Water softening system To ensure good washing results, the dishwasher requires soft water, i.e. containing low amounts of lime, otherwise white limescale will be deposited on the utensils and inner container. Tap water above 9° Clarke must be softened. The water is softened with salt (regeneration salt) in the water softening system of the dishwasher. The setting and therefore the required amount of salt depends on the degree of hardness of your tap water (see table). Setting The amount of salt dispensed can be set from •:‹‹ to •:‹.. Salt is not required at the set value •:‹‹. – Find out about the hardness value of your tap water. Your water utility company will help you with this. – Set value can be found in the water hardness table. – Close the door. – Switch on ON/OFF switch (. – Hold down programme button # and press START button P until •:‹.... is indicated on the digital display. – Release both buttons. The LED for button # flashes and the digital display )" displays the factory setting •:‹…. To change the setting: – Press programme button 3. Each time the button is pressed, the set value increases by one level; when the value of •:‹. has been reached, the display jumps back to •:‹‹ (off). – Press START button P. The chosen setting has now been stored. . % . . # . . &. . . $ . . !!!"!!!!!!!!!!"!! en Special salt $ Using special salt Always refill with special salt immediately before switching on the appliance. This ensures that overrun special salt solution is immediately washed out and does not corrode the rinsing tank. – Open the screw-type cap of the compartment 1J. – Fill the tank with water (only required when switching on the appliance for the first time). – Then add dishwasher salt (not table salt or tablets). The water is displaced and runs out. As soon as the salt refill indicator ` on the fascia is lit, top up the salt. Switching off salt refill indicator/ water softening system If the salt refill indicator ` is impaired (e.g. when using combined detergents containing salt component), it can be switched off. – Proceed as described under “Adjusting the water softening system” and set the value to •:‹‹. The water softening system and salt refill indicator are now switched off. a=Warning Never fill the salt dispenser with detergent. You will destroy the water softening system. * depending on model Using detergents with salt component If combined detergents with a salt component are used, salt can usually be omitted up to a water hardness of 21° dH (37° fH, 26° Clarke, 3.7 mmol/l). If the water hardness is over 21° dH, special salt must be used. en Rinse aid % As soon as the rinse-aid refill indicator h is lit on the fascia, there is still a rinse-aid reserve of 1 – 2 rinsing processes. Refill with rinse aid. The rinse ai...
Otros modelos de este manual:Lavavajillas - SR25M832EU/05 (2.8 mb)
Lavavajillas - SR25M832EU/06 (2.8 mb)
Lavavajillas - SR25M832EU/07 (2.8 mb)
Lavavajillas - SR25M832EU/09 (2.8 mb)