Votos - 0, Puntuación media: 0
(
)
)
|
Resumen del manual
This saves time and prevents problems. Overall condition of the machine . Check spray arm for grease and limescale deposits. If you find such deposits: . Fill detergent dispenser with detergent. Start the appliance without utensils in the programme with the highest rinsing temperature. Clean the appliance with detergents/ appliance cleaners which are particularly suitable for use with dishwashers. . To ensure that the door seal always remains clean and hygienic, regularly clean it with a damp cloth and a little washing-up liquid. . If the appliance is switched off for a prolonged period, leave the door ajar to prevent the formation of an unpleasant odour. Cleaning and maintenance en Never use a steam cleaner to clean your dishwasher. The manufacturer is not liable for any consequential damage. Regularly wipe the front of the appliance and fascia with a damp cloth; water and a little washing up liquid are adequate. Do not use sponges with a rough surface or abrasive detergents, as these could scratch the surfaces. Stainless steel appliances: To prevent corrosion, avoid using sponge cloths or wash them out thoroughly several times before using for the first time. a Warning – Health hazard Never use other domestic detergents, e.g. containing chlorine! Special salt and rinse aid . Check the refill indicators ` and h. If required, refill salt and/or rinse aid. en Cleaning and maintenance Filters The filters 1R keep large foreign objects in the rinsing water away from the pump. These foreign objects may occasionally block the filters. The filter system consists of a coarse filter, a flat fine filter and a microfilter. 1. After each washing cycle check the filters for residue. 2. Unscrew filter cylinder as illustrated and take out filter system. Spray arms Limescale and contaminants in the rinsing water may block nozzles and bearings on the spray arms 12 and 1B. 1. Check outlet nozzles on the spray arms for blockages. 2. Unscrew the upper spray arms 12 (1/4 revolution). 3.Remove any residue and clean filters under running water. 4.Re-install filter system in reverse sequence and ensure that the arrow marks are opposite each other after closing the filter system. 3. Remove the lower spray arm 1Bupwards. 4.Clean spray arms under running water. 5.Re-engage or screw on spray arms. 8.Install filters. 9.Re-insert baskets. 3 Fault, what to do? Experience has shown that you can rectify most faults which occur in daily operation yourself. This ensures that the machine is quickly available to you again. In the following overview you can find possible causes of malfunctions and helpful information for rectifying them. Note If the appliance stops during dishwashing or does not start for no obvious reason, first run the Abort programme function (Reset). (See chapter entitled “Operating the appliance”) a Warning – Don’t forget: Repairs may be carried out by technicians only. If a component has to be replaced, ensure that only original spare parts are used. Improper repairs or use of non-original spare parts may cause considerable damage and put the user at considerable risk. Waste water pump Large food remnants or foreign objects which were not captured by the filters may block the waste water pump. The rinsing water will then be above the filter. Fault, what to do? en In this case: 1. First always disconnect the appliance from the power supply. 2. Take out top basket 1* and bottom basket 1Z. 3. Remove the filters 1R. 4. Scoop out water, use a sponge if required. 5. Prise out the white pump cover (as illustrated) using a spoon. Grip the cover on the crosspiece and lift diagonally inwards. Remove cover completely. 6. Check impeller wheel and remove any foreign objects. 7. Place cover in the original position and press down until it engages (click). en Fault, what to do? Fault table Fault Cause Remedial action “Check water supply” Supply hose kinked. Install supply hose without kinks. display X lights up. Tap turned off. Turn on the tap. Tap jammed or calcified. Turn on the tap. Flow rate must be min. 10 l/min. when water supply is open. Filter in the water supply blocked. Switch off the appliance and pull out the mains plug. Turn off the tap. Unscrew water connection. Clean filter in the supply hose. Screw water connection on again. Check for leaks. Reconnect power supply. Switch on the appliance. Error code “:.. is lit. Error code “:.… is lit. Filters 1R are soiled or blocked. Waste water hose is blocked or kinked. Clean filters. (See Cleaning and maintenance) Install hose without kinks, remove any residue. Siphon connection still sealed. Check connection to siphon and open if required. Error code “:.† is lit. Error code “:.. is lit. Cover on the waste water pump loose. Waste water pump blocked or cover on the waste water pump is not locked in position. Mains voltage too low. Lock cover correctly. (See Waste water pump) Clean pump and lock cover correctly. (See Waste water pump) Not an appliance fault, have the mains voltage...
Otros modelos de este manual:Lavavajillas - SR55M580EU/05 (2.81 mb)
Lavavajillas - SR55M580EU/06 (2.81 mb)
Lavavajillas - SR55M580EU/07 (2.81 mb)
Lavavajillas - SR55M580EU/09 (2.81 mb)