Votos - 0, Puntuación media: 0
(
)
)
|
Resumen del manual
This conserves environmental resources and not least saves you money. The Eco 50° programme is a particularly environmentally friendly programme. According to EU regulation 1016/2010 it is the “Standard programme” which is the most efficient standard cleaning cycle for cleaning normally soiled utensils in terms of the combined energy and water consumption for cleaning these types of utensils. Timer programming * * depending on model You can delay the start of the programme by 3, 6 or 9 hours. 1. Switch on ON/OFF switch (. 2. Keep pressing the Preselected starting time button 0 until the appropriate display 3h, 6h or 9h is lit. 3. Press START button h, timer programming is activated. 4. To delete the preselected starting time, keep pressing the Preselected starting time button 0 until none of the displays 3h, 6h or 9h is lit. You can change your programme selection at any time until the programme starts. End of programme The programme has ended when neither of the two displays ` or X is lit. The end of the programme is also indicated by an acoustic signal. The buzzer volume can be set in 4 stages. Accordingly 0, 1, 2 or 3 displays are lit (see water hardness table). Factory setting: 2. This function can be changed as follows: 1. Open the door. 2. Switch on ON/OFF switch (. 3. Hold down button > P and press START button h until the dry display ` and salt refill indicator )* flash. 4. Release buttons. 5. Keep pressing button > P until the salt refill indicator )* and rinse aid refill indicator )" flash. 6. Release buttons. The refill indicators )* and )" flash and the displays # and + are lit (= Setting 2). The set buzzer volume can be heard. To change the setting: 1. Press the button < H until the required setting has been selected. 2. Press START button h. The displays go out. The selected setting is saved. 3. Close the door. Note To save energy, the dishwasher automatically switches off after the end of the programme. Operating the appliance en Interrupting the programme 1. Open the door. 2. Switch off ON/OFF switch (. The LEDs go out. The programme is saved. If the door was opened on an appliance which has a warm water connection or is heated, first leave the door ajar for several minutes and then close. Otherwise, expansion (pressure) may cause the appliance door to spring open or water to run out of the appliance. 3. To continue the programme, switch on the ON/OFF switch ( again. 4. Close the door. Terminating the programme (Reset) 1. Open the door. 2. Press START button h for approx. 3 sec. until all displays go out. 3. Close the door. The remaining programme sequence for draining the residual water takes approx. 1 minute. Changing the programme When the START button h has been pressed, the programme cannot be changed. The only way a programme can be changed is by Cancel programme (Reset). en Cleaning and maintenance Intensive drying The final rinse uses a higher temperature which improves the drying result. The running time may increase slightly. (Caution if utensils are delicate!) 1. Open the door. 2. Switch on ON/OFF switch (. 3. Hold down button > P and press START button h until the dry display ` and salt refill indicator )* flash. 4. Release buttons. 5. Keep pressing button > P until the salt refill indicator )* and “Check water supply” )2 flash. 6. Release buttons. The displays )* and )2 flash. To change the setting: 1. Press button < H until the display # is lit (Intensive drying on). 2. Press START button h. The displays go out. The setting is saved. 3. Close the door. 2 Cleaning and maintenance A regular inspection and maintenance of your machine will help to prevent faults. This saves time and prevents problems. Overall condition of the machine . Check spray arm for grease and limescale deposits. If you find such deposits: . Fill detergent dispenser with detergent. Start the appliance without utensils in the programme with the highest rinsing temperature. Clean the appliance with detergents/ appliance cleaners which are particularly suitable for use with dishwashers. . To ensure that the door seal always remains clean and hygienic, regularly clean it with a damp cloth and a little washing-up liquid. . If the appliance is switched off for a prolonged period, leave the door ajar to prevent the formation of an unpleasant odour. Never use a steam cleaner to clean your dishwasher. The manufacturer is not liable for any consequential damage. Regularly wipe the front of the appliance and fascia with a damp cloth; water and a little washing up liquid are adequate. Do not use sponges with a rough surface or abrasive detergents, as these could scratch the surfaces. Stainless steel appliances: To prevent corrosion, avoid using sponge cloths or wash them out thoroughly several times before using for the first time. a Warning – Health hazard Never use other domestic detergents, e.g. containing chlorine! Special salt and rinse aid . Check the refill indicators )* and )". If required, refill salt and/or rin...
Otros modelos de este manual:Lavavajillas - S51E40X1GB/18 (1.88 mb)
Lavavajillas - S51E40X1GB/19 (1.88 mb)